פּראָדוקט איבערview
The Emtek 7103 Passage Set is a high-quality knobset designed for doors that do not require a locking mechanism, such as closet doors, hallway doors, or pantry doors. This set includes a Madison Black Knob and a #3 Wrought Steel Rosette with a Flat Black Steel (FBS) finish. It is manufactured by Emtek and includes a standard rotation latch and strike plate. The knobset is designed for a standard 2-1/8 inch door preparation. The standard latch is for a 2-3/8 inch backset, with a 2-3/4 inch backset available if specified.
This image displays the Emtek 7103 Passage Set, featuring a round Madison Black Knob mounted on a rectangular Flat Black Wrought Steel Rosette. The knob has a smooth, glossy black finish, contrasting with the textured matte black finish of the rosette.
סעטאַפּ און ינסטאַלירונג
This section provides instructions for the proper setup and installation of your Emtek 7103 Passage Set.
איידער איר אָנהייבן
- Ensure all components are present: knobset, rosette, latch, strike plate, and mounting screws.
- Verify door thickness and backset requirements. Standard backset is 2-3/8 inches. If 2-3/4 inches is required, ensure you have the correct latch.
- Tools required: Phillips head screwdriver, tape measure, pencil.
ינסטאַללאַטיאָן סטעפּס
- צוגרייטן די טיר: Ensure the door has a standard 2-1/8 inch bore hole for the knobset and a 1-inch bore hole for the latch.
- ינסטאַלירן די לאַטש: Insert the latch into the edge of the door, ensuring the bevel faces the door frame. Secure with screws.
- Install the Exterior Knob/Rosette: Place the exterior knob and rosette assembly through the 2-1/8 inch bore hole, aligning the spindle with the latch mechanism.
- Install the Interior Knob/Rosette: Place the interior knob and rosette assembly onto the spindle, aligning the mounting posts with the holes on the exterior rosette.
- Secure the Assembly: Insert and tighten the mounting screws through the interior rosette into the exterior rosette. Do not overtighten.
- אינסטאַלירן די סטרייק פּלאַטע: Mark and chisel the door frame for the strike plate. Secure the strike plate with screws, ensuring the latch engages smoothly.
- טעסט אָפּעראַציע: Rotate the knobs to ensure the latch retracts and extends freely. Check for smooth operation from both sides of the door.
אַפּערייטינג ינסטראַקשאַנז
The Emtek 7103 Passage Set is designed for doors that do not require locking, such as closet doors, hallway doors, or pantry doors. It allows for free passage from both sides at all times.
- To open the door, simply turn the knob in either direction. The latch bolt will retract, allowing the door to open.
- To close the door, push the door shut. The latch bolt will automatically engage with the strike plate, holding the door closed.
וישאַלט
Proper maintenance will ensure the longevity and smooth operation of your Emtek 7103 Passage Set.
- רייניקונג: Clean the knob and rosette surfaces with a soft, damp cloth. Avoid abrasive cleaners, solvents, or polishes that may damage the finish.
- שמירן: Periodically apply a small amount of silicone-based lubricant to the latch mechanism to ensure smooth operation. Do not use oil-based lubricants as they can attract dust and grime.
- טייטנינג סקרוז: Over time, mounting screws may loosen. Periodically check and gently tighten any loose screws to maintain stability. Do not overtighten.
- דורכקוק: Regularly inspect the knobset for any signs of wear, damage, or misalignment.
טראָובלעשאָאָטינג
| פּראָבלעם | מעגלעך סיבה | לייזונג |
|---|---|---|
| Knob is loose or wobbly. | מאַונטינג סקרוז זענען פרייַ. | Tighten the mounting screws on the interior rosette. |
| Latch does not retract smoothly. | מאַנגל אין לובריקאַציע; דעבריס אין מעכאַניזם. | Apply silicone-based lubricant to the latch bolt. Clean any visible debris. |
| Door does not close properly or rattles. | Strike plate misalignment; worn latch. | Adjust the strike plate position. If latch is worn, consider replacement. |
| Knob is stiff to turn. | Spindle misalignment; internal mechanism friction. | Loosen mounting screws slightly, adjust knob position, then retighten. Lubricate internal mechanism if accessible. |
ספּעסאַפאַקיישאַנז
- מאָדעל: Emtek 7103 Passage Set
- מאַטעריאַל: Wrought Steel
- קנופּ סטייל: Madison Black Knob
- Rosette Style: #3 Rosette
- ענדיקן: Flat Black Steel (FBS)
- טיר פּרעפּ: Standard 2-1/8" bore hole
- באַקקסעט: Standard 2-3/8" (2-3/4" available upon request)
- UPC: 751125555226
וואָראַנטי און שטיצן
Emtek products are manufactured to high-quality standards. For specific warranty information regarding your Emtek 7103 Passage Set, please refer to the documentation provided with your purchase or visit the official Emtek webזייטל. גאַראַנטיע טערמינען און באדינגונגען קענען זיין אַנדערש.
For technical support, product inquiries, or assistance with installation or troubleshooting, please contact Emtek customer service directly. Their contact information can typically be found on their official webזייטל אדער אין דער פּראָדוקט פּאַקאַדזשינג.
פאַבריקאַנט: Emtek
באַאַמטער Webפּלאַץ: www.emtek.com
