הקדמה
This manual provides detailed instructions for the installation, operation, and maintenance of your diymore 8-100V Battery Meter. This device is designed to accurately monitor the voltage, capacity, and temperature of various battery types, including ternary lithium, iron lithium, and lead-acid batteries, within an 8-100V range. It features a clear LCD display, automatic calibration, power-off memory, and voltage alarm reminders for enhanced safety and convenience.
פּראָדוקט פֿעיִקייטן
- ברייט באַטעריע קאָמפּאַטאַבילאַטי: Supports 3-22 series lithium batteries, 3-26 series iron lithium batteries, and 12V, 24V, 36V, 48V, 60V, 72V, 84V lead-acid batteries. Also supports custom voltage settings in the 8-100V range.
- הויך און נידעריק וואָלtagE שרעק: Activates an alarm when battery energy is below 10% or above 100% (overcharge/over-discharge).
- קלאָר לקד ווייַז: Simultaneously shows battery voltage, remaining capacity, and temperature.
- אַדזשאַסטאַבאַל באַקלייט: Configurable backlight brightness and duration.
- High Accuracy & Low Power Consumption: Utilizes a precise measurement algorithm and intelligent SOC algorithm for accurate data. Operating current is less than 20mA, and less than 2mA in power-saving mode.
- מאַכט-אַוועק זכּרון: Retains settings after power loss.
- אָטאַמאַטיק קאַלאַבריישאַן: Ensures consistent accuracy.
- ווערסאַטאַל אַפּלאַקיישאַנז: Suitable for computer rooms, RVs, electric vehicles, energy storage devices, and more.
ספּעסאַפאַקיישאַנז
| באַשרייַבונג | ווערט |
|---|---|
| פאַבריקאַנט | diymore |
| פּראָדוקט מאָדעל נומער | B0FNJ5C171 |
| פּראָדוקט וואָג | 50 ג |
| פּראָדוקט דימענשאַנז (L x W x H) | 6.8 X 3.9 X 1.5 סענטימעטער |
| מאַטעריאַל | אַקרילאָניטרילע בוטאַדיענע סטירענע (אַבס) |
| מאַכט מקור | באַטערי |
| מעאַסורעמענט אַקיעראַסי | +/-0.5 % |
| IP שאַץ | IP 67 |
| מינימום אַפּערייטינג באַנדtage | 8 וואלטס (דק) |
| VoltagE ראַנגע | דק 8-100V |
| דעטעקציע טעמפּעראַטור קייט | -20 צו 80 °C |
| האַכלאָטע | 0.01V |
| אַפּערייטינג קראַנט | ≤20מאַ |
סעטאַפּ און ינסטאַלירונג
The diymore battery meter is designed for straightforward installation. Ensure the power source is disconnected before proceeding with any wiring.
וויירינג אינסטרוקציעס:
- Identify the positive (+) and negative (-) terminals of your battery or power system.
- Connect the red wire from the battery meter to the positive (+) terminal of your battery.
- Connect the black wire from the battery meter to the negative (-) terminal of your battery.
- זיכער מאַכן אַז אַלע פֿאַרבינדונגען זענען זיכער און ריכטיק איזאָלירט צו פאַרמייַדן קורץ קרייזן.
ערשט קאַנפיגיעריישאַן:
After connecting the meter, it will power on. You will need to configure the battery type and series count to ensure accurate readings. Refer to the 'Operating Instructions' section for details on navigating the settings menu.
אַפּערייטינג ינסטראַקשאַנז
The diymore battery meter features a user-friendly interface with multiple operating modes and settings.
אַרויסווייַזן אינטערפּרעטאַציע:
The LCD screen simultaneously displays:
- באַטערי וואָלtage: קראַנט וולtagE פון די פארבונדן באַטאַרייע.
- Remaining Capacity: פּראָצענטtagE פון באַטאַרייע אָפּצאָל רוען.
- טעמפּעראַטור: Real-time ambient temperature (if sensor is active).
Mode Selection and Settings:
The meter offers six primary modes for configuration:
- Ternary Lithium Battery Settings (L-): Configure for ternary lithium batteries by selecting the number of series (e.g., L-03 for 3 series).
- Iron Lithium Battery Settings (F-): Configure for iron lithium batteries by selecting the number of series (e.g., F-03 for 3 series).
- Lead Acid Battery Settings (P-): Configure for lead-acid batteries by selecting the nominal voltage (e.g., P-12 for 12V).
- Custom Voltage Settings (C-): Allows manual input of voltage range for specific battery types not covered by presets.
- Backlight Settings (bL): Adjust backlight brightness and duration.
- הויך און נידעריק וואָלtage Alarm Settings (AL): Set the thresholds for overcharge and over-discharge alarms.
Use the button on the side of the meter to cycle through modes and adjust settings. Long press the button to enter setting mode, short press to change values, and long press again to save and exit.
אַלאַרם פאַנגקשאַנאַליטי:
The meter provides visual and potentially audible alarms for critical battery states.
When the battery capacity exceeds 100% (overcharge) or drops below 10% (over-discharge), the meter will display a warning and activate an alarm to alert the user.
וישאַלט
To ensure the longevity and accurate performance of your diymore battery meter, follow these maintenance guidelines:
- רייניקונג: ווישט אויס דעם דיספלעי און casing with a soft, dry cloth. Avoid using abrasive cleaners or solvents that could damage the screen or plastic.
- ינווייראַנמענאַל טנאָים: Store and operate the meter within its specified temperature range (-20 to 80°C). Avoid exposure to extreme temperatures, direct sunlight for prolonged periods, and high humidity.
- וואַסער קעגנשטעל: The meter has an IP67 rating, meaning it is protected against dust and temporary immersion in water. However, it is not designed for continuous underwater use. Ensure the connections are dry before operation.
- פֿאַרבינדונג אָרנטלעכקייט: Periodically check the wiring connections to ensure they are secure and free from corrosion.
טראָובלעשאָאָטינג
If you encounter issues with your diymore battery meter, refer to the following common problems and solutions:
- קיין ווייַז:
- Check power connections: Ensure the red and black wires are correctly and securely connected to the battery terminals.
- באַשטעטיקן באַטאַרייע וואָלtage: באַשטעטיקן די באַטאַרייע וואָלומעןtage is within the meter's operating range (8-100V DC).
- ומפּינקטלעך רידינגז:
- Incorrect battery type/series setting: Ensure the meter is configured for the correct battery type (Ternary Lithium, Iron Lithium, Lead Acid) and the correct number of series or voltage. Refer to 'Operating Instructions'.
- Recalibration: The meter features automatic calibration, but if readings seem consistently off, re-check settings.
- אַלאַרם אַרבעט נישט:
- Check alarm settings: Verify that the high and low voltage alarm thresholds are set correctly in the 'AL' mode.
- Battery state: Ensure the battery's charge level is actually outside the set thresholds to trigger the alarm.
- ווייַז פליקערינג:
- Unstable power supply: Check for loose connections or fluctuations in the battery voltage.
If problems persist after attempting these troubleshooting steps, please contact diymore customer support for further assistance.
וואָראַנטי און שטיצן
For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official diymore website. Keep your proof of purchase for any warranty claims. If you require assistance, please contact the seller or manufacturer directly.
