JOBY SeaPal Bluetooth Shutter Grip Instruction Manual

הקדמה

The JOBY SeaPal Bluetooth Shutter Grip is designed to enhance your mobile photography and videography experience, especially in challenging environments. It provides superior control over your smartphone's camera, ensuring you capture every moment with ease and precision. Its durable construction offers protection against water, dust, and shocks, making it ideal for various outdoor and aquatic activities.

This manual provides essential information on setting up, operating, and maintaining your SeaPal Bluetooth Shutter Grip to ensure optimal performance and longevity.

וואָס איז אין די קעסטל

• 1 x SeaPal Bluetooth Shutter Grip

סעטאַפּ

Follow these steps to properly set up your JOBY SeaPal Bluetooth Shutter Grip with your SeaPal Waterproof Smartphone Case.

1. Preparing the SeaPal Case

1. Place the Case: Place your SeaPal Waterproof Smartphone Case on a soft, clean surface to prevent scratching the front lens port.
2. Open the Latch: To open the case, push the red release button on the latch and turn the latch away from yourself.
3. Install Bumper Kit: Refer to the detailed instruction manual (available via QR code on packaging) for the correct bumper configuration and placement specific to your phone model. Bumpers simply slide into place without the need for glues or adhesives.
4. אַרײַנשטעלן טעלעפאָן: Remove any existing phone cases from your smartphone. Place your phone inside the SeaPal case with its lens pointing out of the lens port.
5. Close and Secure: Close the rear membrane of the case. Secure the latch by rotating it back into the locking position. Listen for an audible click to confirm it is securely fastened. Test the latch by hand to ensure it is firm.

2. Attaching the Bluetooth Shutter Grip

6. Secure the Grip: Secure the Bluetooth Shutter Grip to the base of the SeaPal case using the supplied mounting screws. Ensure the red shutter button on the grip faces the same direction as the case's lenses. You can use a small flathead screwdriver or a coin to tighten the screws.
7. Power On Grip: Long press the red shutter button on the grip until you see a green light flashing, indicating it is powered on and ready for pairing.
8. Bluetooth Pairing: On your smartphone, open the Bluetooth settings. Locate and connect to the JOBY Shutter Grip.

Once connected, the shutter button on the grip will allow you to take photos and start/stop video recording while your phone is in video mode.

Operating the Shutter Grip

Once your SeaPal Bluetooth Shutter Grip is securely attached and paired with your smartphone, operating it is straightforward:

• גענומען פאָטאָס: With your phone's camera app open, press the red shutter button on the grip to capture a still image.
• רעקאָרדינג ווידעא: Switch your phone's camera app to video mode. Press the red shutter button once to start recording, and press it again to stop recording.
• אונטער וואַסער נוצן: The ergonomic design of the grip provides a secure and comfortable hold, allowing for stable shooting even in dynamic water environments. The Bluetooth connection ensures reliable shutter activation without direct screen interaction.

וישאַלט

Proper maintenance will extend the life of your SeaPal Bluetooth Shutter Grip:

• רייניקונג: After each use, especially in saltwater, rinse the grip thoroughly with fresh water. Wipe it dry with a soft, clean cloth.
• סטאָרידזש: האַלט דעם גריפּ אין אַ קיל, טרוקן אָרט אַוועק פון דירעקט זונשייַן און עקסטרעמע טעמפּעראַטורן.
• באַטערי: The grip features a long-lasting battery designed for years of use. If replacement is ever needed, refer to the full product manual or contact customer support.

טראָובלעשאָאָטינג

If you encounter issues with your SeaPal Bluetooth Shutter Grip, consider the following:

• Not Connecting via Bluetooth: Ensure the grip is powered on (green light flashing). Check your phone's Bluetooth settings to ensure it's discoverable and try re-pairing. Make sure no other devices are interfering with the Bluetooth signal.
• Shutter Button Not Responding: Verify the Bluetooth connection is active. Ensure your phone's camera app is open and in the correct mode (photo or video).
• Water Leakage (Case): While the grip itself is not waterproof, it attaches to the waterproof SeaPal case. Always perform a dry test of the SeaPal case before placing your phone inside and submerging it in water. Ensure all seals are clean and free of debris, and the latch is securely closed.

ספּעסאַפאַקיישאַנז

פּראָדוקט בילדער

Image: The JOBY SeaPal Bluetooth Shutter Grip securely attached to the bottom of a SeaPal Waterproof Smartphone Case, ready for use.

בילד: א דעטאַלירטע view of the ergonomic design of the Bluetooth Shutter Grip, highlighting its textured surface for a firm hold and the red shutter button.

Image: A person demonstrating the attachment of the Bluetooth Shutter Grip to the SeaPal Waterproof Smartphone Case using screws.

Image: A person partially submerged in water, holding the SeaPal case with the attached grip, capturing content.

Image: A person walking along a sandy beach, holding the SeaPal case with the Bluetooth Shutter Grip, showcasinג זײַן פּאָרטאַביליטי.

Image: A person in the water holding the SeaPal case with the grip above the surface, ready to capture a shot.

וואָראַנטי & שטיצן

For warranty information, technical support, or any inquiries regarding your JOBY SeaPal Bluetooth Shutter Grip, please refer to the official JOBY webזייטל אדער קאנטאקט זייער קאסטומער סערוויס דעפארטמענט. האלט אייער קויף קוויטל פאר גאראנטיע טענות.