פאָדספּאָרט אַקסעסאָרי קלamp קיץ פֿאַר FX6 FX6S FX-S מאָטאָרציקל בלועטוט אינטערקאָם כעדסעט באַניצער מאַנואַל

הקדמה

This manual provides instructions for the installation and maintenance of the Fodsports Accessory Clamp Kits, designed for use with Fodsports FX6, FX6S, and FX-S Motorcycle Bluetooth Intercom Headsets. Please read this manual thoroughly before installation to ensure proper use and longevity of the product.

פּראָדוקט איבערview

The Fodsports Accessory Clamp Kit offers versatile mounting solutions for your Fodsports intercom unit. It includes both a traditional clamp and an adhesive mount, along with necessary hardware, to securely attach your intercom to various helmet types.

וואָס איז אין די קעסטל

The Fodsports Accessory Clamp Kit includes the following components:

• Clamp קלאַמער
• Adhesive Mount Base
• מאַונטינג סקרוז
• ל-שייפּט שרויפנ - ציער

בילד באַשרייַבונג: א פולשטענדיקע view of the Fodsports Accessory Clamp Kit components, including the clamp bracket, adhesive mount base, screws, and an L-shaped screwdriver.

סעטאַפּ און ינסטאַלירונג

Before installation, ensure your helmet surface is clean and dry.

Choosing Your Mounting Method

The kit provides two primary methods for attaching your intercom unit to your helmet: the clamp bracket or the adhesive mount base.

Clamp קאַנטיקער ינסטאַלירונג

1. Locate a suitable position on the left side of your helmet, typically between the outer and inner shells, where the clamp can securely grip.
2. לוסאַן די סקרוז אויף די קלamp bracket using the provided L-shaped screwdriver.
3. רוק די קלamp bracket onto the edge of your helmet, ensuring it is firmly seated.
4. פֿעסטצוציען די שרויפֿן צו פֿעסטשטעלן די קל.amp bracket in place. Do not overtighten.
5. Slide your Fodsports intercom unit onto the installed clamp קאַנטיקער ביז עס קליקס אין פּלאַץ.

בילד באַשרייַבונג: א נאָענטע בילד view of the Fodsports clamp bracket, showing its design for gripping the helmet edge.

Adhesive Mount Base Installation

1. Select a flat, clean area on the left side of your helmet for the adhesive mount. Ensure the surface is free from dirt, grease, or moisture.
2. Peel off the protective backing from the adhesive mount base.
3. Press the adhesive mount base firmly onto the chosen helmet surface for at least 30 seconds.
4. Allow the adhesive to cure for at least 24 hours before attaching the intercom unit to ensure maximum bond strength.
5. Slide your Fodsports intercom unit onto the installed adhesive mount base until it clicks into place.

בילד באַשרייַבונג: א נאָענטע בילד view of the Fodsports adhesive mount base, showing the adhesive backing.

Securing the Intercom Unit

אַמאָל די קלamp or adhesive base is securely attached, slide your Fodsports FX6, FX6S, or FX-S intercom unit onto the mounting bracket. Ensure it is fully engaged and feels stable.

Image description: A Fodsports intercom unit securely mounted on the side of a motorcycle helmet using the clamp kit.

Operating the Clamp קיט

די קלamp kit itself does not have operational controls. Its function is to provide a stable and secure mounting point for your Fodsports Bluetooth intercom unit. Once the intercom is attached, refer to the specific user manual for your Fodsports FX6, FX6S, or FX-S intercom for operational instructions regarding its features (e.g., power, pairing, volume, communication).

וישאַלט

• קעסיידער דורכקוקן די קלamp bracket or adhesive mount for any signs of wear, damage, or loosening.
• Ensure all screws on the clamp bracket remain tight. Re-tighten with the L-shaped screwdriver if necessary, but avoid overtightening.
• ריין די קלamp kit components with a soft, damp cloth. Avoid using harsh chemicals or abrasive materials that could damage the plastic or adhesive.
• If using the adhesive mount, periodically check the bond strength. If the adhesive shows signs of weakening, consider replacing the mount or using the clamp קלאַמער.

טראָובלעשאָאָטינג

Intercom Unit Feels Loose on Mount

• קוק Clamp שרויף: אויב איר נוצן די קלamp bracket, ensure the screws are sufficiently tightened.
• Verify Intercom Engagement: Make sure the intercom unit is fully slid onto the mounting bracket until it locks securely.
• דורכקוקן פֿאַר שעדיקן: Examine both the clamp kit and the intercom's mounting slot for any cracks or deformities that might prevent a secure fit.

Adhesive Mount Not Sticking

• ייבערפלאַך צוגרייטונג: Ensure the helmet surface was thoroughly cleaned and dried before application.
• קורינג צייט: Allow the adhesive to cure for the recommended 24 hours before attaching the intercom unit.
• טעמפּעראַטור: Apply the adhesive in a moderate temperature environment (e.g., room temperature) for optimal bonding. Extreme cold or heat can affect adhesion.
• ייבערפלאַך טיפּ: The adhesive works best on smooth, non-porous surfaces.

Clamp Bracket Does Not Fit Helmet Edge

• העלם קאַמפּאַטאַבילאַטי: Some helmet designs may have edges that are too thick or shaped unusually for the standard clamp bracket. In such cases, the adhesive mount base is the recommended alternative.

ספּעסאַפאַקיישאַנז

באַמערקונג: ספּעסאַפאַקיישאַנז זענען אונטערטעניק צו טוישן אָן פריערדיק באַמערקן.

וואָראַנטי און שטיצן

For warranty information or technical support regarding your Fodsports Accessory Clamp Kit, please refer to the documentation included with your original Fodsports intercom unit or visit the official Fodsports website. You may also contact Fodsports customer service directly for assistance.

Official Fodsports Store on Amazon: Fodsports Store