1. הקדמה
This instruction manual provides essential information for the safe and effective installation, operation, and maintenance of your Hella Proj-Light SL60 LED Blue Worklight. Please read this manual thoroughly before attempting to install or operate the product. Retain this manual for future reference.
2. זיכערקייַט אינפֿאָרמאַציע
Always observe the following safety precautions to prevent injury or damage to the product and vehicle.
- Disconnect the vehicle's battery before beginning any electrical work to prevent electrical shock or short circuits.
- ענסורע די אַפּערייטינג וואָלtage of the worklight (10-80V) is compatible with your vehicle's electrical system.
- Do not look directly into the light beam when the light is active, as it may cause eye damage.
- Mount the worklight securely to prevent it from dislodging during vehicle operation.
- Route cables away from hot surfaces, sharp edges, and moving parts to prevent damage.
- ניצט צוגעפאסטע פערזענלעכע שוץ-עקוויפּמענט (PPE) בעת דער אינסטאַלאַציע.
3. פּעקל אינהאַלט
באַשטעטיקן אַז אַלע קאָמפּאָנענטן זענען פאַראַן איידער איר גייט ווייטער מיט דער אינסטאַלאַציע:
- 1 x Hella 996210001 Proj-Light SL60 LED Blue 10-80V Worklight
4. סעטאַפּ און ייַנמאָנטירונג
Follow these steps for proper installation of the Hella Proj-Light SL60 LED Worklight.
4.1 מאַונטינג
Select a suitable mounting location on your vehicle that provides clear visibility and is structurally sound. The worklight comes with an adjustable mounting bracket.
- Position the mounting bracket at the desired location and mark the drilling points.
- Drill pilot holes if necessary, ensuring not to damage any underlying components.
- Secure the bracket using appropriate fasteners (not included, unless specified in package contents).
- Attach the worklight to the bracket using the provided bolt and nut, allowing for angle adjustment.
Figure 1: Hella Proj-Light SL60 LED Worklight showing the mounting bracket and heat sink fins.
4.2 וויירינג
The Hella Proj-Light SL60 is designed for 10-80V DC electrical systems. Ensure correct polarity during connection.
- Identify the positive (+) and negative (-) wires from the worklight.
- Connect the positive wire of the worklight to a switched 10-80V DC power source (e.g., a dedicated switch or existing auxiliary circuit) using appropriate gauge wiring and a fuse.
- Connect the negative wire of the worklight to a reliable ground point on the vehicle chassis.
- Ensure all connections are secure and insulated to prevent short circuits and corrosion.
פיגורע 2: דערציען view of the Hella Proj-Light SL60 LED Worklight with power cable.
4.3 דימענשאַנז
Refer to the diagram below for the physical dimensions of the worklight (measurements in millimeters).
Figure 3: Dimensional drawing of the Hella Proj-Light SL60 LED Worklight.
5. אָפּעראַציע
Once properly installed and wired, the Hella Proj-Light SL60 LED Worklight can be operated via the connected switch.
- Activate the switch to turn the worklight ON.
- Deactivate the switch to turn the worklight OFF.
- Adjust the angle of the worklight by loosening the mounting bolt, repositioning the light, and then securely tightening the bolt.
The blue light projection is designed to enhance safety by indicating the presence and direction of moving vehicles or equipment, such as forklifts in warehouses or industrial settings.
6. וישאַלט און קער
The Hella Proj-Light SL60 LED Worklight is designed for durability and minimal maintenance. Regular inspection and cleaning will ensure optimal performance.
- רייניקונג: Clean the lens and housing periodically with a soft cloth and mild soap solution. Avoid abrasive cleaners or solvents that could damage the lens or finish.
- דורכקוק: Regularly check the mounting hardware for tightness and inspect the wiring for any signs of wear, fraying, or corrosion. Replace any damaged components immediately.
- LED לעבן: The LED elements have an estimated operating life of 50,000 hours and do not require replacement under normal operating conditions.
7. טראָובלעשאָאָטינג
If you encounter issues with your Hella Proj-Light SL60, refer to the following table for common problems and solutions.
| פּראָבלעם | מעגלעך סיבה | לייזונג |
|---|---|---|
| ליכט טוט נישט קער אויף. | No power supply; Blown fuse; Incorrect wiring; Faulty switch. | Check power connections; Inspect and replace fuse if necessary; Verify wiring polarity and connections; Test or replace switch. |
| ליכט איז שוואַך אָדער פליקערט. | נידעריק וואָלtage; Loose connection; Corroded terminals. | קוק פאָרמיטל וואָלtage; Tighten all electrical connections; Clean any corroded terminals. |
| מאַונטינג קלאַמער איז פרייַ. | Fasteners are not tight. | Tighten all mounting bolts and nuts securely. |
8. טעכניש ספּעסאַפאַקיישאַנז
| שטריך | דעטאַל |
|---|---|
| סאָרט | העלאַ |
| מאָדעל | 996210001 |
| Voltage | 10-80 וו דק |
| ליכט טיפּ | געפֿירט וואָרקליגהט |
| ליכט קאָליר | בלוי |
| אַפּערייטינג לעבן | 50,000 שעה |
| דימענשאַנז (פּראָדוקט) | 4 X 5 X 4 אינטשעס (בעערעך) |
| פּונקט וואָג | 12.7 אונסעס |
| מאַנופאַקטורער טייל נומער | 996210001 |
| UPC | 760687177890 |
9. גאַראַנטיע און קונה שטיצע
Hella products are manufactured to high-quality standards and are backed by a manufacturer's warranty against defects in materials and workmanship. Please refer to the warranty documentation provided with your purchase for specific terms and conditions.
For technical assistance, warranty claims, or further inquiries, please contact Hella customer support through their official website or authorized distributors. Keep your proof of purchase and product model number (996210001) readily available when contacting support.
