הקדמה
This manual provides essential information for the proper use, installation, and maintenance of your Secura chainsaw chains. These chains are designed for AL-KO AC310714-38 chainsaws with a 35cm cutting length. Please read this manual thoroughly before installation and operation to ensure safety and optimal performance.
וויכטיק סאַפעטי אינפֿאָרמאַציע
Always prioritize safety when working with chainsaws. While this manual focuses on the chains, general chainsaw safety practices must be followed. Refer to your chainsaw's instruction manual for comprehensive safety guidelines.
- Always wear appropriate personal protective equipment (PPE), including safety glasses, hearing protection, gloves, and protective legwear.
- Ensure the chainsaw is turned off and the spark plug cap is removed (for gasoline models) or the battery is disconnected (for electric models) before performing any maintenance or chain installation.
- האַלטן בייסטאַנדערז, קינדער און אַנימאַלס אַוועק פון די אַרבעט געגנט.
- Inspect the chainsaw and chain for damage before each use.
פּראָדוקט איבערview
This product includes two semi-chisel chainsaw chains, specifically adapted for AL-KO AC310714-38 chainsaws. These chains feature a 35cm cutting length, 3/8LP inch pitch, 49 drive links, and a 1.3mm (0.050") gauge.
פיגורע 1: Two Secura chainsaw chains. These chains are designed for durability and efficient cutting.
Compatibility and Measurement
It is crucial to ensure the correct chain specifications for your chainsaw. Chainsaw models can have different cutting sets, and the total length and cutting length may vary. Different chain systems (e.g., large and small saw teeth) require different drive sprockets. Therefore, it is highly recommended to verify the specifications of your existing chain or chainsaw bar before purchasing or installing a new chain.
Key Chain Specifications:
- קאַטינג לענג: The working length of the guide bar, measured from the chainsaw housing to the tip of the bar when mounted. For these chains, the cutting length is 35cm (approximately 14 inches). This is not the total length of the chain itself.
- פּעך: The distance between three consecutive rivets divided by two. This chain has a 3/8LP (Low Profile) inch pitch.
- מאָס: The thickness of the drive links, which fits into the guide bar groove. This chain has a 1.3mm (0.050") gauge.
- דרייוו לינקס: The number of links on the chain that fit into the guide bar groove. This chain has 49 drive links.
פיגורע 2: Correct measurement of cutting length. The cutting length is measured from the chainsaw body to the tip of the guide bar, not the total length of the bar.
פיגורע 3: How to measure a saw chain. This diagram illustrates how to identify the pitch (Teilung), drive links (Treibglieder), and chain gauge (Nutbreite).
פיגורע 4: Visual representation of the chain specifications: 3/8" LP Pitch, 49 Drive Links, and 1.3 mm Gauge.
Setup (Chain Installation)
Follow these general steps for installing a new chainsaw chain. Always consult your chainsaw's specific instruction manual for detailed installation procedures.
- צוגרייטן די קייט-זעג: Ensure the chainsaw is off, the spark plug cap is removed (if applicable), and the chain brake is engaged.
- Remove the Bar Cover: Loosen the bar nuts and remove the side cover that holds the guide bar in place.
- אַראָפּנעמען די אַלטע קייט (אויב אָנווענדלעך): Carefully remove the old chain and guide bar. Clean any sawdust or debris from the sprocket area and guide bar groove.
- אינסטאַלירן נייע קייט: Place the new chain around the clutch drum sprocket. Ensure the cutting edges of the chain teeth are facing the correct direction (usually forward on the top of the bar).
- בארג גייד באַר: Fit the guide bar over the bar studs and align the drive links of the chain into the groove of the guide bar.
- Replace Bar Cover: צוריקשטעלן די זייט דעקל און האנט-אנצינדן די שטאנג מוטן. נאך נישט אינגאנצן אנציהען.
- אַדזשאַסטירן קייט שפּאַנונג: Adjust the chain tension screw until the chain is snug against the bottom of the guide bar, but can still be pulled freely by hand. There should be no slack on the underside of the bar, and the drive links should not lift out of the bar groove.
- צוציען די באַר-מוטערלעך: Fully tighten the bar nuts while holding the tip of the guide bar up to maintain tension.
- לעצט טשעק: Release the chain brake and manually rotate the chain to ensure it moves smoothly. Re-check tension after a few cuts, as new chains can stretch.
אַפּערייטינג
Once the chain is correctly installed and tensioned, operate your chainsaw according to the manufacturer's instructions. Proper chain tension is critical for safe and efficient operation. An overly loose chain can derail, causing injury or damage. An overly tight chain can cause premature wear to the chain, bar, and sprocket, and can reduce engine power.
- Always ensure the chain is properly lubricated with appropriate bar and chain oil during operation.
- Regularly check chain tension during use, especially during the first hour of operation with a new chain.
- Avoid cutting into dirt, rocks, or metal, as this will dull the chain quickly.
וישאַלט
Regular maintenance extends the life of your chainsaw chain and ensures safe operation.
- שאַרפּנינג: Sharpen the chain regularly to maintain cutting efficiency. These semi-chisel chains are designed to be easy to sharpen. Use a round file of the correct diameter (typically 4.0mm or 5/32" for 3/8LP pitch chains, but verify with your chainsaw manual or chain manufacturer). Maintain the correct filing angles for optimal performance.
- רייניקונג: After each use, clean the chain and guide bar to remove sawdust, resin, and debris. This prevents buildup that can hinder performance and cause wear.
- שמירן: Ensure your chainsaw's automatic oiler is functioning correctly and that the oil reservoir is filled with quality bar and chain oil. Proper lubrication is vital to reduce friction and heat.
- דורכקוק: Periodically inspect the chain for damaged or worn drive links, rivets, and cutters. Replace the chain if significant damage or wear is observed.
טראָובלעשאָאָטינג
| פּראָבלעם | מעגלעך סיבה | לייזונג |
|---|---|---|
| קייט שניידט נישט עפֿעקטיוו | שטאַמפּע קייט, פאַלשער שאַרפֿעניש ווינקל, נישט ריכטיקע קייט שפּאַנונג. | Sharpen the chain, verify sharpening angles, adjust chain tension. |
| קייט דערגיילט זיך פון גייד באַר | לויזע קייט שפּאַנונג, אפגענוצט גייד שטאַנג גרוב, אומרעכטע קייט גרייס. | Adjust chain tension, inspect guide bar for wear, ensure correct chain specifications. |
| Chain smokes or overheats | Insufficient lubrication, overly tight chain, dull chain. | Check oiler function and oil level, adjust chain tension, sharpen chain. |
| Chain binds in wood | Dull chain, improper cutting technique, incorrect chain tension. | Sharpen chain, review cutting technique, adjust chain tension. |
ספּעסאַפאַקיישאַנז
- סאָרט: Secura
- מאָדעל נומער: 6371315
- ASIN: B07KPDNRWL
- קייט טיפּ: Semi-chisel
- קאַטינג לענג: 35 ס״מ (אומגעפער 14 אינטשעס)
- פּעך: 3/8LP (Low Profile)
- מאָס: 1.3 מם (0.050 אינטשעס)
- דרייוו לינקס: 49
- קאַמפּאַטאַבילאַטי: Designed for AL-KO AC310714-38 chainsaws
- פּעקל אינהאַלט: 2 x Chainsaw Chains
וואָראַנטי און שטיצן
Information regarding specific warranty terms for this product is not provided in the available data. For warranty claims or technical support, please contact your retailer or the manufacturer, Secura, directly. Please have your model number (6371315) and ASIN (B07KPDNRWL) available when contacting support.
For general inquiries or to find more information about Secura products, you may visit the brand's official webפּלאַץ אָדער קאָנטאַקט זייער קונה סערוויס אָפּטיילונג.
