1. הקדמה
This manual provides essential instructions for the safe and correct installation, operation, and maintenance of the Satco 80-2627 Two-Light Ballast Bypass Wiring Harness. This harness is designed to convert existing fluorescent fixtures to operate with linear LED T8 lamps that require a ballast bypass (direct wire) installation. Please read all instructions thoroughly before beginning installation.
2. זיכערקייַט אינפֿאָרמאַציע
WARNING: Risk of electric shock. Installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
- Always disconnect power at the circuit breaker or fuse box before installation, servicing, or removing the fixture.
- ענשור די צושטעלן וואָלtage is correct for the LED T8 lampס זייַענדיק אינסטאַלירן.
- דו זאלסט נישט מאַכן אָדער יבערבייַטן קיין עפענען האָלעס אין אַ אָפּצוימונג פון וויירינג אָדער עלעקטריקאַל קאַמפּאָונאַנץ בעשאַס קיט ינסטאַלירונג.
- צו פאַרמייַדן וויירינג שעדיקן אָדער אַברייזשאַן, טאָן ניט ויסשטעלן וויירינג צו עדזשאַז פון בויגן מעטאַל אָדער אנדערע שאַרף אַבדזשעקץ.
- This product is intended for use with specific LED T8 lamps designed for ballast bypass operation. Consult the LED lamp manufacturer's instructions for compatibility and wiring diagrams.
- טראָגט פּאַסיקע פּערזענלעכע שוץ-עקוויפּמענט (PPE) ווי זיכערהייטס-ברילן און הענטשקעס בעת דער אינסטאַלאַציע.
- ענשור אַז אַלע קאַנעקשאַנז זענען זיכער און רעכט ינסאַלייטיד.
3. פּראָדוקט איבערview
The Satco 80-2627 wiring harness simplifies the conversion of a two-lamp fluorescent fixture to operate with ballast bypass LED T8 lamps. It includes pre-wired lamp holders (sockets) and a quick-connect terminal for easy connection to the main power supply.
Image 1: Components of the Satco 80-2627 Ballast Bypass Wiring Harness, showing the pre-wired lamp holders and quick-connect terminal.
4. סעטאַפּ און ייַנמאָנטירונג
Follow these steps carefully to install the Satco 80-2627 wiring harness:
- דיסקאַנעקט מאַכט: Turn off power to the fixture at the circuit breaker or fuse box. Verify power is off using a voltagE טעסטער איידער פּראַסידינג.
- צוטריט פיקסטשער וויירינג: Open the fixture to access the existing ballast and wiring. Remove any covers or diffusers as necessary.
- Remove Existing Ballast: Disconnect all wires from the existing fluorescent ballast. Carefully remove and dispose of the old ballast according to local regulations.
-
אינסטאַלירן נייַ לamp האָלדערס: אַראָפּנעמען די יגזיסטינג לamp holders (sockets) from the fixture. Install the new pre-wired lamp holders from the Satco 80-2627 harness into the fixture, ensuring they are securely seated.
Image 2: Illustration of the easy installation process, showing the harness with new lamp holders ready for connection.
- Wire the Harness: Connect the quick-connect terminal of the Satco 80-2627 harness to the fixture's main power supply wires (Line and Neutral). Ensure proper polarity as indicated by the wiring diagram on the LED T8 lamps or fixture. Typically, one side of the LED T8 lamp receives Line voltage, and the other side receives Neutral. The harness is designed to provide these connections to the lamp האָלדערס.
- זיכער וויירינג: Ensure all wiring is neatly routed and secured, preventing pinching or contact with sharp edges. Replace any wiring covers.
- Install LED T8 Lamps: Insert the ballast bypass LED T8 lamps into the new lamp holders. Ensure they are fully seated and twisted into place.
- Close Fixture: Replace any fixture covers or diffusers that were removed.
- ומקערן מאַכט: Turn power back on at the circuit breaker or fuse box. Test the new LED lighting system.
5. אַפּערייטינג ינסטרוקטיאָנס
Once installed, the Satco 80-2627 Ballast Bypass Wiring Harness operates seamlessly with your fixture's existing wall switch. Simply use the wall switch to turn the LED T8 lamps אויף אָדער אַוועק.
6. וישאַלט
The Satco 80-2627 wiring harness requires minimal maintenance. Periodically, it is recommended to:
- וויסואַל דורכקוק: With power disconnected, visually inspect the wiring and connections for any signs of wear, damage, or loose connections.
- רייניקונג: If necessary, gently wipe down the exterior of the lamp holders with a dry, lint-free cloth. Do not use liquid cleaners near electrical components.
7. טראָובלעשאָאָטינג
If you encounter issues after installation, refer to the following troubleshooting guide:
| פּראָבלעם | מעגלעך סיבה | לייזונג |
|---|---|---|
| Lamps do not turn on. |
|
|
| Lampס פליקער אָדער טונקל. |
|
|
If troubleshooting steps do not resolve the issue, contact a qualified electrician or Satco customer support.
8. ספּעסאַפאַקיישאַנז
- מאָדעל נומער: 80-2627
- פאַבריקאַנט: סאַטקאָ
- טייל נומער: 80-2627
- פּראָדוקט דימענשאַנז: אומגעפער 10 x 10 x 10 אינטשעס (פאקעט)
- נומער וואָג: 1 פונט
- מאַכט מקור: קאָרדעד עלעקטריק
- נומער פון לampס שטיצט: צוויי (2)
- קאַמפּאַטאַבאַל לamp טיפּ: Linear LED T8 Lamps (Ballast Bypass / Direct Wire)
- אַרייַנגערעכנט קאַמפּאָונאַנץ: Satco 80-2627 Two Light Ballast Bypass Wiring Harness
9. וואָראַנטי אינפֿאָרמאַציע
For warranty information regarding the Satco 80-2627 Two-Light Ballast Bypass Wiring Harness, please contact the manufacturer directly. Warranty terms and conditions may vary.
קאָנטאַקט פאַבריקאַנט: Refer to Satco's official webזייטל אדער פּראָדוקט פּאַקאַדזשינג פֿאַר די מערסט אַקטועלע קאָנטאַקט דעטאַלן.
10. שטיצן
If you require further assistance or have questions not covered in this manual, please contact Satco customer support. Ensure you have your product model number (80-2627) available when contacting support.
סאַטקאָ Webפּלאַץ: www.satco.com
