1. הקדמה
The Hercules 8500 DHWT Hot Wire Foam Cutter Table is designed for precise cutting, forming, and sculpting of various foam materials, including Styrofoam. This tool is suitable for a wide range of applications, from architectural modeling and set design to crafting and hobby projects. It features an adjustable temperature control and a foot control pedal for hands-free operation, enhancing both precision and safety.
This manual provides essential information for the safe and effective use of your foam cutter. Please read it thoroughly before operation and retain it for future reference.
2. זיכערקייַט אינפֿאָרמאַציע
- עלעקטריקאַל זיכערקייַט: Ensure the unit is connected to a grounded 110/120V AC outlet. Do not operate with wet hands or in damp conditions. Always unplug the unit when not in use or before performing maintenance.
- Hot Wire Hazard: The cutting wire becomes extremely hot during operation. Avoid direct contact with the wire to prevent burns. Keep flammable materials away from the hot wire.
- ווענטילאַטיאָן: Operate the foam cutter in a well-ventilated area. Cutting foam can produce fumes that may be irritating or harmful if inhaled in large quantities.
- אויג שוץ: Always wear safety glasses to protect your eyes from any debris or fumes.
- סטאַביל ייבערפלאַך: Place the foam cutter on a stable, level, and heat-resistant surface to prevent tipping or accidental movement during operation.
- קינדער און פּעץ: האַלטן קינדער און פּעץ אַוועק פון די אַפּערייטינג געגנט.
- אַנאַטענדיד אָפּעראַציע: Never leave the foam cutter unattended while it is powered on.
3. פּעקל אינהאַלט
באַשטעטיקן אַז אַלע זאכן זענען פאַראַן ביים אויספּאַקן:
- Hercules 8500 DHWT Foam Cutter Table (Corded 110V AC)
- Over-arm assembly
- Foot Control Pedal
- Spool with cutting wire (Φ0.18mm, length 5m)
- Adjustable Angle Stop with Extension Rail
- Circle Cutter Accessory
4. סעטאַפּ און אַסעמבלי
Follow these steps to assemble your Hercules 8500 DHWT Foam Cutter Table:
- Attach the Over-arm: Secure the over-arm to the main unit. Ensure it is firmly seated.
- פֿאַרבינדט דעם גראַונד דראָט: Locate the ground wire eyelet and the Phillips-head screw on the underside of the over-arm. Remove the screw, run the ground wire through the eyelet, and re-attach the screw to the over-arm. This step is critical for safe operation. Leaving the ground wire detached or incorrectly attached can cause permanent damage to the unit.
- Install Cutting Wire: Carefully thread the cutting wire from the spool through the designated points on the over-arm and the table. Ensure the wire is taut but not overly stressed.
- פאַרבינדן פֿוס פּעדאַל: Plug the foot control pedal into the designated port on the unit.
- Position Accessories: Place the adjustable angle stop or circle cutter accessory as needed for your specific cutting task.
5. אַפּערייטינג ינסטרוקטיאָנס
- מאַכט אויף: Plug the unit into a standard 110/120V AC outlet. Flip the main power switch to the "ON" position.
- סטרויערן טעמפּעראַטור: Use the temperature control knob to set the desired heat level for the cutting wire. Start with a lower setting and gradually increase it until the wire cuts smoothly through your specific foam material. Different foam types and thicknesses require different temperatures. The adjustable temperature goes up to 390 degrees Fahrenheit.
- פֿיס פּעדאַל אָפּעראַציע: The foot control pedal allows for hands-free activation of the hot wire. Press the pedal to heat the wire and release it to cool. This provides precise control over cutting.
- Cutting Foam:
- Place the foam material on the cutting surface.
- Use the integrated grid and protractor, along with the adjustable angle stop or circle cutter, to guide your cuts.
- Gently push the foam into the heated wire. Do not force the material, as this can bend the wire or result in an uneven cut. Allow the heat to melt through the foam.
- Maintain a steady, consistent speed for clean cuts.
- מאַכט אַוועק: When finished, turn off the main power switch and unplug the unit from the wall outlet. Allow the wire to cool completely before handling or storing.
6. וישאַלט
- רייניקונג: Regularly clean the cutting surface and over-arm with a soft, dry cloth. Ensure the unit is unplugged and cool before cleaning. Do not use abrasive cleaners or solvents.
- Wire Replacement: The cutting wire is a consumable part and will eventually break or wear out. Replace the wire as needed using the provided spool or compatible replacement wire (Φ0.18mm). Refer to the setup instructions for proper wire installation.
- סטאָרידזש: Store the foam cutter in a clean, dry place, away from direct sunlight and extreme temperatures.
7. טראָובלעשאָאָטינג
| פּראָבלעם | מעגלעך סיבה | לייזונג |
|---|---|---|
| Wire not heating | Unit not plugged in; Power switch off; Foot pedal not pressed; Broken wire; Faulty connection. | Check power connection; Turn on power switch; Press foot pedal; Replace cutting wire; Inspect wire connections. |
| Wire breaks frequently | Temperature too high; Forcing foam too quickly; Wire tension too high; Old/fatigued wire. | Reduce temperature setting; Cut slower, allow heat to do the work; Adjust wire tension; Replace wire. |
| אַניוואַן קאַץ | Inconsistent cutting speed; Wire not taut; Foam not properly guided; Over-arm not square. | Maintain steady speed; Ensure wire is taut; Use guides/fences; Check over-arm alignment. |
| Unit gets excessively hot (transformer) | Unit left plugged in for extended periods without use. | Unplug the unit when not in use. This is normal behavior for the transformer, but unplugging prevents unnecessary heat generation. |
8. ספּעסאַפאַקיישאַנז
- מאָדעל: 8500 DHWT
- מאַכט אַרייַנשרייַב: 110/120V AC, 50-60 Hz
- מאַטעריאַל: Aluminum (Table surface, Handle, Over-arm)
- בלייד מאַטעריאַל: High Carbon Steel (for cutting wire)
- ענדיקן טיפּ: Non-stick (working surface)
- Over-arm Throat: 13.75 אינטשעס (אומגעפער 35 ס״מ)
- Over-arm Height: 6 אינטשעס (אומגעפער 15 ס״מ)
- Cutting Wire Diameter: Φ0.18מם
- אַדזשאַסטאַבאַל טעמפּעראַטור: Up to 390 degrees Fahrenheit
- נומער וואָג: 9.13 פונט (אומגעפער 4.14 ק"ג)
- פּעקל דימענשאַנז: 16.85 x 13.27 x 4.96 אינטשעס (אומגעפער 42.8 x 33.7 x 12.6 ס״מ)
- UPC: 855170001827
9. וואָראַנטי און שטיצן
For warranty information, technical support, or to purchase replacement parts, please contact Hercules customer service. Refer to the product packaging or the official Hercules webזייטל פֿאַר איצטיקע קאָנטאַקט דעטאַלן.
Webפּלאַץ: www.herculescutters.com
