DROK L298 דואַל H-בריק DC מאָטאָר דרייווער (מאָדעל 200206) ינסטרוקציע מאַנואַל

1. הקדמה

This manual provides detailed instructions for the DROK L298 Dual H-Bridge DC Motor Driver, Model 200206. This module is designed for controlling the speed and direction of two independent DC motors. It features a wide input voltage range, high current capability, and integrated protection mechanisms, making it suitable for various industrial and hobby applications.

Figure 1: DROK L298 Dual H-Bridge DC Motor Driver (Model 200206)

2. ספּעסאַפאַקיישאַנז

Figure 2: Physical Dimensions of the Motor Driver

3. סעטאַפּ און וויירינג

Proper wiring is crucial for the safe and effective operation of the motor driver. Refer to the diagram below for connection points.

Figure 3: Wiring Diagram and Pinout

3.1 מאַכט קאַנעקשאַנז

• Main Power Input (6.5V-27V): Connect your DC power supply to the green screw terminal labeled "6.5-27V" and "GND". Ensure the polarity is correct (+ to + and - to -). A 15A fuse is recommended in series with the positive power input.
• Logic Power Input (+5V): The module requires a separate 5V logic power supply. Connect a stable 5V DC source to the "+5V" pin on the control signal header and its corresponding "GND" pin. Note: The logic supply voltage should match the control signal voltage from your microcontroller (e.g., 3.3V for a 3.3V microcontroller).

3.2 מאָטאָר קאַנעקשאַנז

• מאָטאָר 1 רעזולטאַט: Connect the first DC motor to the screw terminals labeled "OUT1" and "OUT2".
• מאָטאָר 2 רעזולטאַט: Connect the second DC motor to the screw terminals labeled "OUT3" and "OUT4".
• Each motor output port is rated for 7A. It is advisable to include a 10A fuse in series with each motor for protection.

3.3 Control Signal Connections

The control signals are typically provided by a microcontroller (e.g., Arduino). The module supports two independent motors.

• Motor 1 Control:
  • IN1, IN2: These digital input pins control the direction of Motor 1.
  • ENA (PWM1): This pin enables Motor 1 and accepts a Pulse Width Modulation (PWM) signal for speed control.
• Motor 2 Control:
  • IN3, IN4: These digital input pins control the direction of Motor 2.
  • ENB (PWM2): This pin enables Motor 2 and accepts a PWM signal for speed control.

4. אַפּערייטינג ינסטרוקטיאָנס

The DROK L298 Dual H-Bridge Motor Driver allows for precise control over DC motors. The following tables outline the logic for controlling motor direction and speed.

4.1 Motor Direction Control (for Motor 1, using IN1 and IN2)

Note: The same logic applies to Motor 2 using IN3 and IN4.

4.2 Motor Speed Control (using ENA/PWM1 or ENB/PWM2)

Motor speed is controlled by applying a Pulse Width Modulation (PWM) signal to the ENA (for Motor 1) or ENB (for Motor 2) pin. The PWM signal should have a frequency range of 0-10KHz.

• A 0% duty cycle PWM signal will result in the motor being off.
• A 100% duty cycle PWM signal will result in the motor running at full speed.
• Intermediate duty cycles will adjust the motor speed proportionally.

Exampלאַ: To run Motor 1 forward at 50% speed, set IN1 to HIGH, IN2 to LOW, and apply a 50% duty cycle PWM signal to ENA.

4.3 Operational Demonstration

5. וישאַלט

• רייניקונג: Keep the module free from dust and debris. Use a soft, dry brush or compressed air for cleaning. Avoid using liquids.
• ינווייראַנמענאַל טנאָים: Operate the module within its specified temperature and humidity ranges. Avoid exposure to extreme temperatures, moisture, or corrosive environments.
• פֿאַרבינדונגען: קאָנטראָלירט פּעריִאָדיש אַלע דראָט פֿאַרבינדונגען צו זיכער מאַכן אַז זיי זענען זיכער און פֿרײַ פֿון קעראָוזשאַן. לויזע פֿאַרבינדונגען קענען פֿירן צו אומגעריכטע אָפּעראַציע אָדער שאָדן.
• היץ מאַנאַגעמענט: While the module is designed for efficient operation, ensure adequate ventilation, especially when driving motors at high currents or for extended periods.

6. טראָובלעשאָאָטינג

• מאָטאָר רעאַגירט נישט:
  • Verify all power connections (main power and logic power) are correctly wired and supplied with the correct voltage.
  • Check motor connections for proper polarity and secure contact.
  • Ensure control signals (IN1/IN2 or IN3/IN4) are correctly applied and the ENA/ENB pin is receiving a valid PWM signal.
  • Confirm the motor itself is functional by testing it directly with a power source.
• Motor Runs Only at Full Speed or Not at All:
  • Check the PWM signal on the ENA/ENB pin. Ensure it is within the 0-10KHz frequency range and has a varying duty cycle for speed control.
  • Verify that the logic power supply voltage matches the control signal voltage from your microcontroller. A mismatch can cause incorrect logic interpretation.
• מאָדול איבערהיצונג:
  • Ensure the motor current does not exceed the rated 7A per channel.
  • Provide adequate ventilation around the module.
  • Check for short circuits in the motor wiring or the motor itself.
• אונטער וואָלtage שוץ טריגערד:
  • The module has built-in under voltage protection. If the input voltage drops below a certain threshold, the module may cease operation to prevent damage.
  • Verify your main power supply can provide sufficient voltage and current under load.

7. וואָראַנטי און שטיצן

DROK products are designed for reliability and performance. For specific warranty information, please refer to the product packaging or contact DROK customer support directly. Technical assistance and further resources may be available through the official DROK webפּלאַץ אָדער אָטערייזד דיסטריביאַטערז.

פֿאַר נאָך שטיצע, ביטע באַזוכט די DROK Store on Amazon.