בענינקאַ טו.גאָ 2WV

BENINCA TO.GO 2WV Remote Control Transmitters User Manual

Model: TO.GO 2WV (OR-481)

1. הקדמה

This manual provides essential instructions for the setup, operation, and maintenance of your BENINCA TO.GO 2WV remote control transmitters. These devices are designed to operate garage doors or gate openers using a 433.92 MHz rolling code frequency, ensuring secure and reliable access. Please read this manual thoroughly before attempting to use or program the remote controls.

Five BENINCA TO.GO 2WV remote control transmitters, black with two white buttons each.

This image displays five BENINCA TO.GO 2WV remote control transmitters. Each remote is black with two distinct white buttons, designed for operating garage doors or gates. The image highlights the compact and ergonomic design of the keyfobs.

2. אויפשטעלן און פּראָגראַמירן

The BENINCA TO.GO 2WV remote controls utilize a rolling code technology for enhanced security. Programming typically involves pairing the remote with your BENINCA receiver unit. Specific programming steps may vary depending on your receiver model. Always refer to the instruction manual of your gate or garage door opener for detailed programming procedures.

2.1. Battery Installation (If Required)

Your remote control comes with a pre-installed battery. If replacement is needed, carefully open the remote casing (usually by unscrewing a small screw or prying gently at a designated notch). Insert the new battery, ensuring correct polarity (+/-). Typically, these remotes use a CR2032 type battery.

2.2. General Programming Steps (Consult Receiver Manual)

  1. צוטריט צום ריסיווער: Locate the control unit or receiver for your gate/garage door opener. This unit usually has a 'Learn' or 'Prog' button.
  2. Activate Learning Mode: Press and release the 'Learn' or 'Prog' button on the receiver. An LED indicator on the receiver will typically light up or flash, indicating it is in learning mode.
  3. Transmit Code: Within a few seconds (usually 5-10 seconds), press and hold the desired button on your new BENINCA TO.GO 2WV remote control for 2-3 seconds.
  4. באַשטעטיקונג: The receiver's LED will usually flash or change color to confirm successful programming. Release the remote button.
  5. טעסט אָפּעראַציע: After programming, wait a few seconds, then test the remote control by pressing the programmed button.

Note: Some BENINCA systems allow programming a new remote from an existing, already programmed remote (master remote cloning). Refer to your specific system's documentation for this advanced feature.

3. אָפּעראַציע

אַמאָל פּראָגראַמירט, איז עס גאַנץ פּשוט צו אַרבעטן מיט אייער BENINCA TO.GO 2WV ווײַטקאָנטראָל:

  • עפן / פארמאכן: Point the remote control towards your gate or garage door opener and press the programmed button. The gate/door should activate.
  • אפשטעלן: Pressing the button again while the gate/door is in motion will typically stop its movement.
  • קייט: Ensure you are within the operational range of your receiver. Obstructions or interference can affect the range.

4. וישאַלט

4.1. באַטערי פאַרבייַט

If the remote's LED indicator does not light up, or if the operational range significantly decreases, the battery may need replacement. Follow the battery installation steps in Section 2.1.

4.2. רייניקונג

Clean the remote control with a soft, dry cloth. Avoid using abrasive cleaners or solvents, as these can damage the casing or internal components. Do not expose the remote to excessive moisture.

4.3. סטאָרידזש

Store the remote control in a dry place, away from direct sunlight and extreme temperatures. Avoid placing heavy objects on the remote.

5. טראָובלעשאָאָטינג

פּראָבלעםמעגלעך סיבהלייזונג
ווייַט טוט נישט אַרבעטן.Dead or low battery. Not programmed correctly. Out of range.Replace battery. Re-program the remote (Section 2.2). Move closer to the receiver.
פאַרקלענערטע אַפּערייטינג קייט.Low battery. Interference. Obstructions.Replace battery. Check for sources of radio interference. Ensure clear line of sight to receiver.
די LED אויף דער ווײַטקאָנטראָל צינדט זיך נישט אָן.Dead battery. Faulty remote.Replace battery. If problem persists, the remote may be faulty and require replacement.
Gate/door opens intermittently.Weak signal. Receiver issue.Check remote battery. Ensure receiver antenna is clear. Consult your gate/door opener manual for receiver troubleshooting.

6. ספּעסאַפאַקיישאַנז

  • סאָרט: BENINCA
  • מאָדעל: טו.גאָ 2WV
  • טייל נומער: OR-481
  • אָפטקייַט: 433.92 מהז
  • קאָדירונג: ראָולינג קאָד
  • קנעפּלעך: 2
  • פאַבריקאַנט: בענינקאַ
  • ASIN: B01NBCM4AZ

7. שטיצן און וואָראַנטי

For further assistance, technical support, or warranty inquiries, please contact the seller or BENINCA customer service. Specific warranty terms and conditions may apply and are typically provided with your purchase documentation.

Please note that this manual provides general guidance. Always refer to the specific instructions provided with your BENINCA gate or garage door opener system for precise programming and operational details.

פֿאַרבונדענע דאָקומענטן - טו.גאָ 2WV

Preview בענינקאַ טינקי אַוואַנסירטע ראָולינג קאָד טויער אָטאָמאַציע סיסטעם
א פולשטענדיגע אנווייזונג צום בענינקא טינקי טויער אויטאמאטיזאציע סיסטעם, וואס באדעקט אינסטאלאציע, פראגראמירן, פונקציעס, און פראבלעם-לייזונג. לערנט וועגן פארגעשריטענע ראָולינג קאוד טעכנולוגיע פאר פארבעסערטע זיכערהייט.
Preview בענינקאַ BE.CODE פּראָגראַמירבאַר דיגיטאַל קיפּאַד מאַנואַל
דאָס דאָקומענט גיט אינסטרוקציעס און טעכנישע ספּעציפֿיקאַציעס פֿאַר די Beninca BE.CODE פּראָגראַמירבאַרע דיגיטאַלע קיפּאַד, אַ דראָטלאָזע מיטל פֿאַר קאָנטראָלירן אויטאָמאַטישע טויער און טיר סיסטעמען.
Preview בענינקאַ BRAINY קאָנטראָל יוניט - טעכנישער מאַנואַל און ספּעציפֿיקאַציעס
א פולשטענדיגע טעכנישע האנטבוך פארן בענינקא BRAINY קאנטראל איינהייט, מיט פרטים וועגן אינסטאלירונג, פראגראמירן, פונקציעס, זיכערהייט אייגנשאפטן, און פראבלעם-לייזונג פאר טויער אויטאמאטיזאציע סיסטעמען.
Preview Beninca ZED24/ZED24E Electromechanical Actuator for Tilt-Up Doors - Installation and User Manual
Comprehensive guide for the Beninca ZED24 and ZED24E electromechanical actuators, covering installation, operation, safety, and technical specifications for tilt-up doors. Includes multilingual safety instructions and a detailed parts list.
Preview Beninca BEN24 Knikarm Poortopener and CP.BN Sturing Installatiehandleiding
אינסטרוקציעס פֿאַר ינסטאַלירונג און באַניצער-האַנדל פֿאַר די בענ24 בענ24 קנואַר פּאָטאָפּענער און די CP.BN אַפּערייטינג סיסטעם. טעכניש ספּעסאַפאַקיישאַנז, מאנטיקtagE- ינסטרוקטיאָנס, פאַרבינדן סטשעמאַ ס, פּראָגראַממעראָפּטיעס און וועהיקלעס.
Preview בענינקאַ RR.1WBV און RR.2WBV ראָולינג קאָוד ראַדיאָ ריסיווערס אָפּערייטינג אינסטרוקציעס
דאס דאקומענט גיט אפערירן אינסטרוקציעס פאר בענינקא RR.1WBV און RR.2WBV ראָולינג קאוד ראדיא ריסיווערס. עס באהאנדלט אייגנשאפטן, אינסטאלירונג עצה, און דעטאלירטע פראצעדורן פארן מעמערירן טראנסמיטערס און פראגראמירן פארשידענע פונקציעס.