Keithley 2303-PJ Power Supply Instruction Manual
Model: 2303-PJ
1. פּראָדוקט איבערview
The Keithley 2303-PJ is a specialized power supply designed for testing portable, battery-operated devices. It offers advanced capabilities to simulate a battery's performance across a wide range of conditions, including output resistance and voltage response. This instrument is crucial for accurately testing device charge control circuitry and overall battery simulation.
שליסל פֿעיִקייטן אַרייַננעמען:
- Ultra-fast response to transient load currents
- Variable output resistance
- 100nA DC current sensitivity
Figure 1: Front panel of the Keithley 2303-PJ Power Supply. The display shows voltage and current readings (e.g., 3.60V, 1.08A). Controls include a navigation pad, 'DISPLAY', 'MENU', 'OPERATE', 'ENTER', 'SET' buttons, and a 'POWER' button with indicator lights.
2. סעטאַפּ
- אַנפּאַק און דורכקוק: Carefully remove the instrument from its packaging. Inspect for any signs of damage during transit. Report any damage to the shipping carrier and Keithley immediately.
- מאַכט קשר: Connect the supplied AC power cord to the instrument's rear panel power inlet and then to a grounded AC power outlet. Ensure the power source matches the instrument's voltagE באדערפענישן.
- ערשט מאַכט אויף: דרוק די מאַכט button located on the front panel. The display should illuminate, indicating the unit is operational.
- Connecting to Device Under Test (DUT): Use appropriate test leads to connect the output terminals of the 2303-PJ to the device you intend to test. Observe correct polarity.
- ווענטילאַטיאָן: Ensure adequate ventilation around the instrument. Do not block the ventilation grilles on the sides or rear of the unit.
3. אַפּערייטינג ינסטרוקטיאָנס
3.1 פראָנט פּאַנעל קאָנטראָלס
- ווייַז: ווייזט ארויסגאַנג באַנדtage, current, and other operational parameters.
- נאַוויגאַציע קנעפּלעך (אַרויף, אַראָפּ, לינקס, רעכטס): Used to navigate through menus and adjust parameter values.
- ENTER קנעפּל: Confirms selections or entered values.
- SET קנעפּל: Enters parameter setting mode.
- MENU קנעפּל: Accesses the main menu for configuration and advanced settings.
- OPERATE Button: Toggles the output on or off.
- אַרויסווייַז קנעפּל: Cycles through different display modes or views.
3.2 יקערדיק אָפּעראַציע
- באַשטעטיקן וואָלtage און קראַנט:
- דרוק די שטעלן קנעפּל.
- Use the navigation buttons to select the voltage or current parameter you wish to adjust.
- Use the navigation buttons (typically Up/Down) to change the value.
- דרוק אַרייַן צו באַשטעטיקן די באַשטעטיקן.
- מעגלעכן ארויסגאַנג:
- Once parameters are set, press the אָפּערירן button to enable the power output. The output indicator should illuminate.
- To disable the output, press אָפּערירן ווידער.
- מאָניטאָרינג רידינגז:
The display continuously shows the actual output voltage and current. Use the DISPLAY button to cycle through different measurement viewס אויב בנימצא.
4. וישאַלט
- רייניקונג: Keep the instrument clean by wiping the exterior with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure the unit is powered off and disconnected from the AC supply before cleaning.
- ווענטילאַטיאָן: Periodically check that the ventilation grilles are free from dust and debris to ensure proper airflow and prevent overheating.
- סטאָרידזש: When not in use for extended periods, store the instrument in a clean, dry environment within its specified operating temperature and humidity ranges.
- קאליבראציע: For optimal performance and accuracy, periodic calibration by qualified personnel is recommended. Refer to the Keithley service manual or contact Keithley support for calibration procedures and intervals.
5. טראָובלעשאָאָטינג
| פּראָבלעם | מעגלעך סיבה | לייזונג |
|---|---|---|
| דאָס אינסטרומענט גייט נישט אָן. | No AC power; faulty power cord; internal fuse blown. | Check AC power connection and outlet. Try a different power cord. If fuse is suspected, contact qualified service personnel. |
| קיין רעזולטאַט וואָלtagE/קראַנט. | Output disabled; incorrect settings; overload protection active; faulty connections. | דרוק אָפּערירן to enable output. Verify voltage/current settings. Check for short circuits or overloads on the DUT. Ensure test leads are securely connected. |
| Unstable or inaccurate readings. | Poor connections; external interference; instrument needs calibration. | Check all connections for looseness or corrosion. Ensure the instrument is away from strong electromagnetic fields. Consider professional calibration. |
| אָוווערכיטינג. | Blocked ventilation; excessive ambient temperature; continuous operation at maximum load. | Ensure ventilation grilles are clear. Operate in a cooler environment. Reduce load or allow for cool-down periods. |
For issues not listed here or if troubleshooting steps do not resolve the problem, please contact Keithley technical support.
6. ספּעסאַפאַקיישאַנז
| פּאַראַמעטער | ווערט |
|---|---|
| פאַבריקאַנט | Keithley |
| טייל נומער | 2303-PJ |
| נומער מאָדעל נומער | 2303-PJ |
| פּונקט וואָג | 5.44 קג |
| פּעקל דימענשאַנז | 48.26 X 33.02 X 22.86 סענטימעטער |
| נומער פּעקל קוואַנטיטי | 1 |
| באַטעריז פארלאנגט? | ניין |
| ערשטער דאַטע בנימצא | 4 נאוועמבער 2016 |
7. וואָראַנטי און שטיצן
Warranty information for the Keithley 2303-PJ Power Supply is typically provided with the product at the time of purchase or can be found on the official Keithley webזייטל. ביטע באַהאַלטן אייער קויפן באַווייַז פֿאַר וואָראַנטי קליימז.
For technical support, service, or calibration inquiries, please contact Keithley customer service directly. Refer to the contact information provided in your product documentation or on the official Keithley webפּלאַץ (www.tek.com/keithley).