UHPPOTE HBK-A02 125KHz RFID Standalone Door Access Control Keypad User Manual

1. הקדמה

This manual provides detailed instructions for the installation, programming, operation, and maintenance of the UHPPOTE HBK-A02 125KHz RFID Standalone Door Access Control Keypad. This device is designed to provide secure access control for various applications, supporting up to 1000 card users.

Figure 1: UHPPOTE HBK-A02 Keypad Front View

2. שליסל פֿעיִקייטן

• High quality and high security, sensitively and response quickly.
• Full programming from the keypad, support add/delete cards, set password, etc.
• Door bell button support external doorbell.
• Uses high-performance MCU for stable performance and low-power circuit for extended service life.
• Functions as a standalone keypad, no computer connection required.
• Suitable for factories, houses, residential quarters, offices, and mechanical/electrical control equipment.

3. ספּעסאַפאַקיישאַנז

4. ינסטאַלירונג

Proper installation is crucial for the optimal performance and security of your access control keypad. Ensure all power is disconnected before beginning installation.

4.1 מאָנטירן די קלאַוויאַטור

1. Choose a suitable mounting location near the door, ensuring it is protected from direct weather exposure if installed outdoors.
2. Use the provided mounting screws to secure the back plate of the keypad to the wall.
3. Route the necessary wiring through the wall or conduit to the keypad's connection point.
4. Attach the keypad front panel to the back plate after wiring is complete.

Figure 2: Keypad Mounted on a Door Frame

4.2 וויירינג קאַנעקשאַנז

The HBK-A02 keypad requires a 12V DC power supply. Carefully follow the wiring diagrams below. Incorrect wiring can damage the device or connected components.

פיגורע 3: דערציען View of Keypad with Wiring Harness

Figure 4: Close-up of Wiring Terminal Block

4.2.1 Common Power Supply Diagram

This diagram illustrates connections when using a single power supply for both the keypad and the electric lock.

Figure 5: Common Power Supply Wiring Diagram

4.2.2 Special Power Supply Diagram

This diagram shows connections when using a dedicated access control power supply unit, which often includes battery backup and advanced control features.

Figure 6: Special Power Supply Wiring Diagram

5. פּראָגראַממינג

The keypad is programmed directly using the numeric buttons. The default master code is 123456.

5.1 אַרייַן פּראָגראַממינג מאָדע

1. דרוק *.
2. Enter the 6-digit Master Code (default: 123456).
3. דרוק #.
4. The red LED will flash, indicating programming mode.

5.2 Exiting Programming Mode

דרוק * to exit programming mode at any time.

5.3 טשאַנגינג די בעל קאָד

1. אַרייַן פּראָגראַממינג מאָדע.
2. דרוק 0.
3. Enter the new 6-digit Master Code.
4. Enter the new 6-digit Master Code again to confirm.
5. דרוק #.
6. אַרויסגאַנג פּראָגראַממינג מאָדע.

5.4 Adding User Cards/Codes

The keypad supports up to 1000 user cards or codes.

1. אַרייַן פּראָגראַממינג מאָדע.
2. דרוק 1.
3. For RFID cards: Present the card to the keypad. The keypad will beep to confirm. Repeat for additional cards.
4. For User Codes: Enter a 4-digit to 6-digit user code, then press #. Enter the code again and press # צו באַשטעטיקן.
5. אַרויסגאַנג פּראָגראַממינג מאָדע.

5.5 Deleting User Cards/Codes

1. אַרייַן פּראָגראַממינג מאָדע.
2. דרוק 2.
3. For RFID cards: Present the card to the keypad. The keypad will beep to confirm deletion. Repeat for additional cards.
4. For User Codes: Enter the 4-digit to 6-digit user code to delete, then press #.
5. אַרויסגאַנג פּראָגראַממינג מאָדע.

5.6 Setting Relay Unlock Time

This sets how long the door remains unlocked after a valid access. The default is 5 seconds.

1. אַרייַן פּראָגראַממינג מאָדע.
2. דרוק 3.
3. Enter a 2-digit number for the unlock time in seconds (e.g., 05 פֿאַר 5 סעקונדעס, 00 פֿאַר 0.2 סעקונדעס).
4. דרוק #.
5. אַרויסגאַנג פּראָגראַממינג מאָדע.

6. אָפּעראַציע

6.1 Gaining Access

• Using an RFID Card: Present a registered RFID card to the keypad. The keypad will beep, and the door will unlock for the set duration.
• ניצן אַ באַניצער קאָד: Enter your registered user code (4-6 digits) followed by #. The keypad will beep, and the door will unlock for the set duration.

6.2 טיר-גלאָק פונקציע

דרוק די גלאָק button on the keypad to activate an external doorbell (if connected).

7. וישאַלט

• רייניקונג: Wipe the keypad surface with a soft, dry cloth. Avoid using abrasive cleaners or solvents.
• ענוויראָנמענטאַל שוץ: Ensure the keypad is protected from extreme temperatures, direct sunlight, and moisture to prolong its lifespan.
• רעגולער טעסטינג: Periodically test the keypad's functionality, including card/code access and the exit button, to ensure proper operation.

8. טראָובלעשאָאָטינג

9. זיכערקייַט אינפֿאָרמאַציע

• שטענדיק אָפּשטעקן די מאַכט איידער איר דורכפירן קיין וויירינג אָדער וישאַלט.
• Ensure all wiring connections are secure and insulated to prevent short circuits.
• שטעלט נישט אויס דעם אפאראט צו וואסער אדער איבעריגע הומידיטי.
• This device is intended for low-voltage applications (12V DC). Do not connect to higher voltage מקורים.
• די אינסטאַלאַציע זאָל דורכגעפירט ווערן דורך קוואַליפֿיצירטע פּערסאָנעל אויב איר זענט נישט זיכער וועגן עלעקטרישע וויירינג.