1. הקדמה
This manual provides comprehensive instructions for the GENIUS KILO TX2 JL remote control. Please read this manual carefully before using the device to ensure proper operation and to maximize its lifespan. Keep this manual for future reference.
2. פּראָדוקט איבערview
The GENIUS KILO TX2 JL is a two-button remote control designed for gate and garage door opener systems. It operates on a frequency of 868.35 MHz, providing reliable communication with compatible receivers.
- מאָדעל: KILO TX2 JLC
- אָפטקייַט: 868.35 מהז
- קנעפּלעך: 2
- קאַמפּאַטאַבילאַטי: Compatible with GENIUS 868 systems and various gate opener remote controls including CASALI JA332, CASALI JA332 Grey, GENIUS JA332, GENIUS JA332 GREY, POWERDOOR JA332, POWERDOOR JA332 GREY, and GENIUS JA332 ORANGE.
- קאָמפּאַטיבלע ראַסיווערז: JA335, 6100075, 6100146, 6100229, 6100230.
פיגורע 1: פראָנט view of the GENIUS KILO TX2 JL remote control. This image displays the white remote with two distinct circular buttons and the 'GENIUS' brand name at the bottom.
פיגורע 2: צוריק view of the GENIUS KILO TX2 JL remote control. This image shows the reverse side of the remote, featuring the model number '6100332 (KILO TX2 JLC)', '868 MHz', 'Made In IE', and the 'CE 0470' marking.
3. סעטאַפּ
3.1. באַטאַרייע ייַנמאָנטירונג
The GENIUS KILO TX2 JL remote control requires one CR2 battery. The remote is typically supplied with a battery already installed. If replacement is needed, follow these steps:
- Locate the battery compartment on the remote control. This is usually secured by small screws or a clip.
- עפֿנט פֿאָרזיכטיק דעם אָפּטייל מיט אַ קליינעם שרויפנציהער אויב נייטיק.
- אַראָפּנעמען די אַלט CR2 באַטאַרייע.
- Insert a new CR2 battery, ensuring the correct polarity (+ and -) is observed.
- פאַרמאַכן די באַטאַרייע אָפּטייל סיקיורלי.
באַמערקונג: אָפּזאָגן געוויינט באַטעריז ריספּאַנסאַבלי לויט די היגע רעגיאַליישאַנז.
3.2. פּראָגראַממינג די רימאָוט קאָנטראָל
Programming the GENIUS KILO TX2 JL remote control involves linking it to your specific gate or garage door opener receiver. The exact programming procedure can vary depending on the model of your receiver.
General steps often include:
- צוטריט צום ריסיווער: Locate the programming button or switch on your gate or garage door opener's receiver unit. This unit is typically located near the motor.
- Activate Learning Mode: Press and release the programming button on the receiver. An indicator light (LED) on the receiver will usually illuminate or flash, indicating it is in learning mode.
- Transmit Code: Within a few seconds of activating learning mode, press and hold the desired button on your new GENIUS KILO TX2 JL remote control.
- באַשטעטיקן פּראָגראַמירן: The receiver's indicator light will typically change (e.g., flash rapidly, turn solid, or turn off) to confirm that the remote control has been successfully programmed.
- טעסט אָפּעראַציע: After programming, test the remote control by pressing the programmed button to ensure it operates your gate or garage door correctly.
וויכטיק: Always refer to the instruction manual provided with your specific gate or garage door opener system for detailed and accurate programming instructions. If you are replacing an existing remote, some systems allow for cloning from an already programmed remote.
4. אַפּערייטינג ינסטרוקטיאָנס
Once programmed, operating the GENIUS KILO TX2 JL remote control is straightforward:
- עפן / פארמאכן: Press the programmed button on the remote control once to activate your gate or garage door opener. Pressing it again will typically stop or reverse the operation, depending on your system's configuration.
- קייט: The remote has a maximum range of 10 meters. Ensure you are within this range for reliable operation. Environmental factors and obstacles can affect the effective range.
5. וישאַלט
5.1. באַטערי פאַרבייַט
If the remote control's range decreases significantly or the indicator light (if present) does not illuminate when a button is pressed, the battery may need replacement. Refer to Section 3.1 for battery installation instructions. Use only CR2 alkaline batteries.
5.2. רייניקונג
Clean the remote control with a soft, dry cloth. Do not use abrasive cleaners, solvents, or immerse the device in water, as this can damage the internal components.
6. טראָובלעשאָאָטינג
| פּראָבלעם | מעגלעך סיבה | לייזונג |
|---|---|---|
| ווייַט קאָנטראָל טוט נישט אַרבעטן. | Dead or low battery. Incorrect programming. Out of range. | Replace the battery (CR2). Re-program the remote control (refer to Section 3.2). Move closer to the receiver. |
| פאַרקלענערטע אַפּערייטינג קייט. | Low battery. Interference from other devices. Obstructions. | Replace the battery. Check for sources of interference. Ensure a clear line of sight to the receiver if possible. |
| Gate/door opens intermittently. | Weak battery. Environmental factors. | Replace the battery. Ensure the remote is not exposed to extreme temperatures or moisture. |
If troubleshooting steps do not resolve the issue, contact your gate or garage door opener system installer or manufacturer for further assistance.
7. ספּעסאַפאַקיישאַנז
| שטריך | דעטאַל |
|---|---|
| סאָרט | זשעני |
| מאָדעל נומער | KILO TX2 JLC |
| אָפטקייַט | 868.35 מהז |
| נומער פון קנעפּלעך | 2 |
| באַטערי טיפּ | 1 x CR2 (Alkaline) |
| מאַקסימום קייט | 10 מעטער |
| קאַנעקטיוויטי טעכנאָלאָגיע | ראַדיאָ פרעקווענסי |
| קאַמפּאַטאַבאַל דעוויסעס | Genius 868 systems |
| ספּעציעלע שטריך | Universal compatibility with listed models |
8. וואָראַנטי און שטיצן
Warranty information for the GENIUS KILO TX2 JL remote control is typically provided by the retailer or manufacturer at the time of purchase. Please retain your proof of purchase for warranty claims.
For technical support, programming assistance beyond the general steps provided, or warranty inquiries, please contact the authorized Genius dealer or the customer support department of your gate or garage door opener system manufacturer.
