מאַניואַלז+

Trust ACM-1000

טראַסט ACM-1000 ווירעלעס איינגעבויטע סוויטש באַניצער מאַנואַל

Model: ACM-1000 (Manufacturer ID: 71015)

1. הקדמה

This manual provides detailed instructions for the installation, operation, and maintenance of your Trust ACM-1000 Wireless Built-in Switch. Please read this manual carefully before installation and use to ensure safe and correct operation. Keep this manual for future reference.

The Trust ACM-1000 is designed to wirelessly control lights or other electrical devices up to 1000W. Its compact design allows for discreet installation in various locations.

2. זיכערקייַט אינפֿאָרמאַציע

ווארענונג: Electrical installation should only be performed by a qualified electrician. Always disconnect power at the main fuse box before performing any electrical work.

3. פּראָדוקט איבערview

The Trust ACM-1000 is a compact wireless receiver designed to be integrated into your existing electrical system.

Trust ACM-1000 Wireless Built-in Switch, front view

פיגורע 1: פראָנט view of the Trust ACM-1000 Wireless Built-in Switch. This image shows the compact, white casing of the switch, with visible wiring terminals at the bottom, a fuse compartment, and an indicator light. The overall design is circular with flat sides for mounting.

3.1 קאַמפּאָונאַנץ

Trust ACM-1000 Wireless Built-in Switch, wiring terminals

פיגורע 2: נאָענט-אַרויף view of the wiring terminals on the Trust ACM-1000. Labels for Live (L), Neutral (N), Input (IN), and Output (OUT) connections are clearly visible, indicating where electrical wires should be connected for power and load control.

Trust ACM-1000 Wireless Built-in Switch, top view with fuse

פיגורע 3: Top view of the Trust ACM-1000, highlighting the fuse compartment labeled "T5A H250V" and the small indicator light. This view also shows the mounting tabs on the sides of the device.

Trust ACM-1000 Wireless Built-in Switch, side view

פיגורע 4: זייַט view of the Trust ACM-1000, showing its slim profile and mounting clips. This view emphasizes the compact nature of the device, suitable for discreet installations.

4. סעטאַפּ און ייַנמאָנטירונג

Before starting, ensure you have all necessary tools and that the power supply is disconnected.

4.1 Wiring the ACM-1000

  1. דיסקאַנעקט מאַכט: Turn off the main power supply at your circuit breaker. Verify with a voltagE tester.
  2. צוגרייטן ווירעס: Strip approximately 8-10mm of insulation from the Live (L), Neutral (N), and load wires (IN/OUT).
  3. פאַרבינדן מאַכט אַרייַנשרייַב:
    • Connect the main Live wire to the terminal marked L.
    • Connect the main Neutral wire to one of the terminals marked N.
  4. Connect Load Output:
    • Connect the Neutral wire of your light/device to the other terminal marked N.
    • Connect the Live wire of your light/device to the terminal marked OUT.
    • If using an existing switch, connect the switched Live wire from the switch to the terminal marked IN.
  5. זיכער ינסטאַלירונג: Place the ACM-1000 in a suitable location such as a ceiling rose, junction box, or cabinet. Ensure it is securely mounted and wires are properly insulated.

Note: For outdoor use, the ACM-1000 must be installed inside an IP44-rated waterproof junction box to protect it from environmental elements.

4.2 Pairing with a Transmitter

The ACM-1000 needs to be paired with a Trust Smart Home transmitter (e.g., remote control, wall switch, motion sensor) to function wirelessly.

  1. ומקערן מאַכט: Turn on the main power supply. The indicator light on the ACM-1000 should illuminate briefly.
  2. אַרייַן די פּערינג מאָדע: Press the small pairing button on the ACM-1000 once. The indicator light will start flashing slowly.
  3. אַקטיווירן טראַנסמיטער: Within 10 seconds, press the 'ON' button (or the desired channel button) on your Trust Smart Home transmitter.
  4. באַשטעטיקונג: The indicator light on the ACM-1000 will flash rapidly a few times and then turn off, indicating successful pairing.
  5. טעסט: Use the transmitter to switch the connected device ON and OFF.

To pair additional transmitters, repeat steps 2-4. The ACM-1000 can store up to 6 different pairing codes.

4.3 Deleting Pairing Codes

To delete a single pairing code or all stored codes:

5. אַפּערייטינג ינסטרוקטיאָנס

Once installed and paired, the Trust ACM-1000 operates seamlessly with your Trust Smart Home transmitter.

6. וישאַלט

7. טראָובלעשאָאָטינג

פּראָבלעםמעגלעך סיבהלייזונג
Device does not respond to transmitter.
  • נישט ריכטיק צוגעפּאַסט.
  • טראַנסמיטער באַטאַרייע נידעריק/טויט.
  • אויס פון קייט.
  • Power to ACM-1000 is off.
  • Re-pair the ACM-1000 with the transmitter (see Section 4.2).
  • פאַרבייַטן די טראַנסמיטער באַטעריז.
  • Move transmitter closer to the ACM-1000.
  • Check power supply to the ACM-1000.
Connected light/device does not turn on.
  • Blown fuse in ACM-1000.
  • אומרעכט וויירינג.
  • די דעווייס אליין איז דעפעקטיוו.
  • Exceeded maximum load.
  • Disconnect power and replace fuse (T5A H250V).
  • Disconnect power and check wiring connections (see Section 4.1).
  • Test the connected device directly.
  • פאַרזיכערן גאַנץ וואָסtagE טוט נישט יקסיד 1000W.
די אינדיקאַטאָר ליכט צינדט זיך נישט אָן.
  • No power to the ACM-1000.
  • דעפעקטיווע איינהייט.
  • Check main power supply and wiring.
  • קאָנטאַקט קונה שטיצן.

8. ספּעסאַפאַקיישאַנז

9. וואָראַנטי און שטיצן

Trust products are manufactured to high quality standards. In the unlikely event of a defect during the warranty period, please contact your retailer or the Trust customer support for assistance. Please retain your proof of purchase.

For the latest information, FAQs, and support, please visit the official Trust website or refer to the product page where you purchased the item.