1. הקדמה
This manual provides instructions for the installation, operation, and maintenance of the Pentair 24800-0121 Air Bleed Assembly. This component is a replacement part designed for use with Sta-Rite System 2 PLM Series pool and spa sand filters, specifically models PLM100 and PLM150. Proper installation and maintenance ensure efficient operation of your pool filtration system.
2. זיכערקייַט אינפֿאָרמאַציע
Always observe basic safety precautions when installing and maintaining pool equipment. Failure to follow these instructions can result in serious injury or property damage.
- Ensure all power to the pump and filter system is turned off and disconnected before beginning any work.
- Relieve all pressure from the filter system before opening or servicing.
- טראָגן צונעמען פערזענלעכע פּראַטעקטיוו עקוויפּמענט, אַזאַ ווי זיכערקייַט ברילן און גלאַווז.
- If you are unsure about any step, consult a qualified pool service professional.
3. פּעקל אינהאַלט
באַשטעטיקן אַז אַלע קאָמפּאָנענטן זענען פאַראַן און נישט געשעדיגט איידער איר גייט ווייטער מיט דער אינסטאַלאַציע.
- Pentair 24800-0121 Air Bleed Assembly (1 unit)
Figure 1: The Pentair 24800-0121 Air Bleed Assembly. This image shows the clear plastic tube with a blue mesh filter at one end, designed to allow air to escape the filter system while retaining filter media.
4. ינסטאַלירונג
This section outlines the steps for replacing the air bleed assembly in your Sta-Rite System 2 PLM Series sand filter.
- צוגרייטן די פילטער סיסטעם: Turn off the pool pump and disconnect its power supply. Close any valves leading to and from the filter to isolate it.
- Relieve System Pressure: Open the air relief valve on top of the filter tank to release any trapped air and pressure. Ensure the pressure gauge reads zero before proceeding.
- Drain the Filter: Open the drain plug at the bottom of the filter tank to allow water to drain completely.
- צוטריט צו דער אלטער אסיפה: Depending on your specific PLM model (PLM100 or PLM150), you may need to remove the filter tank lid or access panel to reach the existing air bleed assembly. Refer to your main filter manual for specific access procedures.
- אַראָפּנעמען די אַלטע פֿאַרזאַמלונג: Carefully detach the old air bleed assembly. It is typically secured by a fitting or clips. Note its orientation for correct installation of the new part.
- אינסטאַלירן די נייע פֿאַרזאַמלונג: Insert the new Pentair 24800-0121 Air Bleed Assembly into its designated position. Ensure it is securely fastened and properly oriented.
- צוריקשטעלן דעם פילטער: Close the filter tank lid or access panel, ensuring all seals and O-rings are correctly seated and lubricated. Close the filter drain plug.
- Restore System Pressure: Open the valves to and from the filter. With the air relief valve still open, turn on the pool pump. Allow water to fill the filter tank and air to escape through the air relief valve.
- Close Air Relief Valve: Once a steady stream of water emerges from the air relief valve, close it. Check for any leaks around the filter system.
Video 1: This video demonstrates the replacement process for a similar air bleed kit (WC8-126Z) compatible with Pentair Sta-Rite filters. While not identical to the 24800-0121, it provides a visual guide to the general steps involved in replacing an air bleed assembly in a pool filter system.
5. אָפּעראַציע
The air bleed assembly functions automatically to release trapped air from the filter tank during operation. This ensures proper water flow and filtration efficiency. After installation, monitor your filter's pressure gauge. If pressure builds up rapidly or water flow is significantly reduced, ensure the air relief valve is functioning correctly and that no air is trapped in the system.
6. וישאַלט
Regular maintenance of your air bleed assembly helps prolong its lifespan and ensures optimal filter performance.
- דורכקוק: Periodically inspect the air bleed assembly for signs of wear, cracks, or damage. Check the mesh screen for any debris accumulation.
- רייניקונג: If the mesh screen appears clogged, carefully remove the assembly (following the installation steps in reverse) and rinse it thoroughly with clean water. Do not use harsh chemicals or abrasive tools.
- פאַרבייַט: Replace the air bleed assembly if it shows significant wear, damage, or if you experience persistent air-related issues with your filter system that cannot be resolved by cleaning.
7. טראָובלעשאָאָטינג
| פּראָבלעם | מעגלעך סיבה | לייזונג |
|---|---|---|
| Air trapped in filter system | Air bleed assembly clogged or damaged; improper installation. | Inspect and clean or replace the air bleed assembly. Ensure proper installation and that the air relief valve is opened during startup. |
| רידוסט וואַסער לויפן | Clogged air bleed assembly, preventing proper air release. | Clean or replace the air bleed assembly. Check other filter components for clogs. |
| Water leaking from assembly area | Improperly seated assembly or damaged O-rings/seals. | Turn off pump, relieve pressure, and re-seat the assembly. Inspect and replace any damaged O-rings or seals. |
8. ספּעסאַפאַקיישאַנז
- טייל נומער: פּענטער 24800-0121
- קאַמפּאַטאַבילאַטי: Sta-Rite System 2 PLM Series Pool and Spa Sand Filters (Models PLM100, PLM150)
- מאַטעריאַל: פּלאַסטיק
- קאָליר: Clear plastic with blue mesh
- נומער וואָג: 0.32 ounces (approximately 0.02 pounds)
- פּראָדוקט דימענשאַנז: 1 X 1 X 1 אינטשעס (בעערעך)
9. וואָראַנטי און שטיצן
פֿאַר וואָראַנטי אינפֿאָרמאַציע אָדער טעכנישע שטיצע, ביטע זען די באַאַמטער פּענטער webזייטל אדער קאנטאקטירן פענטאייר קאסטומער סערוויס גלייך. האלט אייער קויף קוויטל אלס באווייז פון קויפן.
