אַסענד קאָמפּאָנענטן קאָמפּיוטער מאָונט
פּראָדוקט אינפֿאָרמאַציע
ספּעסאַפאַקיישאַנז:
- קאָמפּאַטיבל מיט: גאַרמין און וואַהאָאָ קאָמפּיוטערס
- נויטיקע געצייג: 4 מ״מ עלען שליסל, 5 מ״מ עלען שליסל, 2.5 מ״מ עלען שליסל
פּראָדוקט באַניץ אינסטרוקציעס
Removal of Bolts and Insert:
- Use the 2.5mm allen key to remove the 2 small bolts from the mount.
- To remove the plastic insert, push the top cap bolt upwards.
Mounting the Computer Mount:
- Use a 5mm allen key to remove the top cap from your bike and loosen the stem steerer bolts.
- Ensure your steerer tube sits approximately 3mm lower than the top of the stem or top headset spacer.
- Place the top cap computer mount on the bike and tighten the bolt with a 4mm allen key. Make sure the cutouts in the mount are placed at 6 and 9 o’clock.
- Tighten the stem steerer bolts and place the plastic insert on the top cap, orientating it based on your computer – vertically for Garmin and horizontally for Wahoo.
לעצטע סטעפּס:
Finish by refitting and tightening the two small screws using the 2.5mm hex key. Ensure the setup matches your specific computer model.
ווי אזוי צו פּאַסן די Ascend Components קאָמפּיוטער מאָונט
א דאנק פארן קויפןasing an Ascend Components Computer Mount. The guide will take you through a few basic steps to ensure you orientate the mount correctly. The mounts are compatible with both Garmin and Wahoo computers but require a slightly different set up depending on which computer you have.
מכשירים פארלאנגט
- 4MM allen key, 5MM allen key, 2.5MM allen key
ינסטאַללאַטיאָן ינסטראַקשאַנז
- Remove the 2 small bolts from the mount using the 2.5mm allen key
- Remove the plastic insert by pushing the top cap bolt upwards
- Remove the top cap from your bike with a 5mm allen key and loosen your stem steerer bolts. Check your steerer tube sits approximately 3mm lower than the top of the stem or top headset spacer.
- Place your top cap computer mount on to the bike and tighten the bolt with a 4mm allen key.
IMPORTANT – the 2 cutouts in the mount should be placed at 6 and 9 o’clock.
- Tighten your stem steerer bolts and place the plastic insert on to your top cap. Orientate the insert depending on your computer. Garmin orientated vertically and Wahoo orientated horizontally.
- Finish by refitting and tightening the two small screws using the 2.5mm hex key. In the exampאונטן האָבן מיר עס אויפגעשטעלט פֿאַר אַ גאַרמין מאָונט.
FAQ
פ: קען איך ניצן דעם מאונט מיט אנדערע קאמפיוטער בראַנדז אַחוץ גאַרמין און וואַהאָאָ?
A: The Ascend Components Computer Mount is specifically designed for Garmin and Wahoo computers for optimal compatibility and fit. We do not recommend using it with other brands.
פ: ווי אזוי קען איך צופּאַסן דעם ווינקל פֿון מײַן קאָמפּיוטער ווען עס איז מאָנטירט אויף דעם מאָונט?
A: The angle of your computer display can be adjusted by orienting the plastic insert accordingly - vertically for Garmin and horizontally for Wahoo.
דאָקומענטן / רעסאָורסעס
 |
אַסענד קאָמפּאָנענטן קאָמפּיוטער מאָונט [pdf] אינסטרוקציע מאַנואַל קאָמפּיוטער מאָונט, קאָמפּיוטער, מאָונט |