How can I power on two Flipsky FSESC 110100 controllers using a single power button when connected via CAN bus?

The Flipsky FSESC 110100 features a built-in latching power switch circuit that differs from the older 75100 models. Because this model does not have a dedicated "PWR.ON" signal wire integrated into the CAN bus port, the controllers cannot natively share a power-on signal through the CAN cable alone.To use a single button for both controllers, you have two primary options:Option 1: Parallel Wiring (Hardware Hack): You can attempt to wire the two-pin power switch connectors of both ESCs in parallel to a single physical button. However, this is only recommended if you are comfortable with custom wiring and ensuring the polarities match, as the internal switch circuits may interfere with each other.Option 2: Use an External Antispark Switch: The most reliable method for dual-ESC setups is to leave the individual ESC power buttons in the "ON" position (or bridged) and use a single high-current Antispark Switch between the battery and both ESCs. This allows one button to control the main power flow to the entire system simultaneously.Option 3: Dual Buttons: As you noted, the standard configuration for this model requires two separate buttons because the power logic is localized to each unit's internal PCB.Note: While the VESC_TOOL software allows for communication over CAN once powered, it cannot "wake up" a secondary ESC if that unit's physical power circuit is open. Always ensure both units are powered before attempting to configure them as a Master/Slave pair in VESC_TOOL.

FLIPSKY FSESC 110100

FLIPSKY FSESC 110100 High Voltage 110V Electronic Speed Controller User Manual

1. הקדמה

This manual provides comprehensive instructions for the safe and efficient operation of your FLIPSKY FSESC 110100 High Voltage Electronic Speed Controller (ESC). Please read this manual thoroughly before use to ensure proper setup and to prevent damage to the device or connected components.

2. פּראָדוקט איבערview

The FLIPSKY FSESC 110100 is a high-performance electronic speed controller designed for demanding applications such as fighting robots, electric surfboards, and AGV robots. It features an aluminum PCB for enhanced heat dissipation and supports high voltagE ינפּוץ.

FLIPSKY FSESC 110100 High Voltage ESC with main cables

פיגורע 2.1: פראָנט view of the FLIPSKY FSESC 110100 High Voltage ESC, showing the main power input and motor phase wires.

FLIPSKY FSESC 110100 High Voltage ESC with included accessories

Figure 2.2: The FSESC 110100 ESC along with its various connection cables and accessories, including a USB cable and sensor wires.

3. ספּעסאַפאַקיישאַנז

Detailed specifications of FLIPSKY FSESC 110100

Figure 3.1: Manufacturer's detailed specifications for the FSESC 110100.

פירמוואַרע: 6.05 (אָדער העכער)
Voltage: 14-110V (safe for 4-26S battery configurations)
קעסיידערדיק קראַנט: 50V/120A; 110V/100A (Note: Values depend on mounting, ambient temperature, and air/water circulation)
פּלאַצן קראַנט: 250 א
BEC: 5V@3A
שטיצט מאָדעס: BLDC, FOC (sinusoidal)
ERPM: 150000
קאָמוניקאַציע פּאָרץ: USB, CAN, UART, SPI, IIC
שטיצט סענסאָרס: ABI, HALL, AS5047, AS5048A
Input Source Support: PPM, ADC, NRF, UART
Sensorless Operation: יא
רעגענעראַטיווע קאַפּאַציטעט: יא
פּראָגראַממאַבלע: Via VESC_TOOL
דימענסיעס: 117.70 X 62.40 X 21.70 מם
Motor/Power Wire Size: 10AWG
Phase Filter: יא
מאַכט באַשטימען קנעפּל: רויט
CPU: SMT32F405 with 168MHz frequency
מאַטעריאַל: Aluminum Alloy (for PCB)
וואָג: 0.3 קילאָגראַמס

שליסל פֿעיִקייטן:

Adjustable protection against: low voltagE, הויך באַנדtage, over current, temperature abnormalities, MOSFETs/motor over-temperature.
Supports various control modes: Current, Duty cycle, Speed, PID control.
Designed with Aluminum PCB for good heat dissipation and extended lifespan.
Integrates single serial port function and Bluetooth module for convenient parameter connection and real-time data reading.
Built-in power on/off switch.

4. Component Identification and Wiring

Understanding the various ports and connections is crucial for correct setup. Refer to the diagrams below for detailed identification.

Figure 4.1: Comprehensive wiring diagram illustrating connections for battery, motor, and various communication/sensor ports.

דעטאַילעד view of FLIPSKY FSESC 110100 ports

פיגורע 4.2: נאָענט-אַרויף view of the various communication and sensor ports on the FSESC 110100, with labels for each connection.

פּאָרט דיסקריפּשאַנז:

B+ / B-: Main battery positive and negative connections.
Motor Phase Wires (A, B, C): Connect to the motor's three phase wires.
LED: סטאַטוס גראדן ליכט.
וסב: For connecting to a computer for configuration via VESC_TOOL.
UART: Universal Asynchronous Receiver/Transmitter port for communication with external devices (e.g., Bluetooth module, display).
קענען: Controller Area Network bus for multi-ESC setups.
SPI: Serial Peripheral Interface.
IIC: Inter-Integrated Circuit (I2C) bus.
קאָרידאָר: Hall sensor input for sensored motor operation.
PPM: Pulse Position Modulation input for remote control.
אַדק: Analog-to-Digital Converter input for analog controls.
NRF: Nordic Radio Frequency module support.
מאַכט סוויטש: Red button for power control.

5. סעטאַפּ אינסטרוקציעס

זיכערקייַט ערשטער: Ensure all power sources are disconnected before making any connections. Wear appropriate safety gear.
מאָונטינג: Securely mount the FSESC 110100 in a location with adequate airflow for heat dissipation. The aluminum PCB is designed for good heat transfer, but proper mounting is still essential.
באַטערי קשר: Connect your battery pack (4-26S, 14-110V) to the B+ (positive) and B- (negative) terminals. Ensure correct polarity.
מאָטאָר קשר: Connect the three phase wires from your motor to the A, B, and C terminals on the ESC. If using a sensored motor, connect the Hall sensor cable to the HALL port.
קאָנטראָל אַרייַנשרייַב: Connect your chosen control input (e.g., PPM receiver, UART device) to the corresponding port.
Initial Configuration (VESC_TOOL):
Download and install the latest VESC_TOOL software from the official VESC project website or FLIPSKY support page.
Connect the FSESC 110100 to your computer via the USB port.

Launch VESC_TOOL and follow the motor setup wizard to configure your motor and ESC parameters. This includes motor detection, battery voltage limits, current limits, and control mode settings.
Save your configuration to the ESC.
Bluetooth Module (Optional): If using the integrated Bluetooth module, you can connect to the ESC via a mobile app (e.g., VESC Tool app) for real-time data monitoring and parameter adjustment.

6. אַפּערייטינג ינסטרוקטיאָנס

מאַכט אויף: After completing all connections and configuration, press the red power switch button to power on the ESC. The LED indicator will illuminate.
קאָנטראָל: Operate your device using the configured input source (e.g., remote control, joystick). The ESC will translate your commands into motor control.
מאָניטאָרינג: Use VESC_TOOL or a connected Bluetooth app to monitor real-time data such as motor RPM, current, voltage, and temperature during operation.
שוץ פֿעיִקייטן: The ESC is equipped with various protection features (low/high voltage, over current, over temperature). If a protection limit is reached, the ESC may reduce power or shut down to prevent damage. Identify and resolve the cause of the protection activation.
מאַכט אַוועק: When finished, press the red power switch button to power off the ESC.

7. וישאַלט

רעגולער דורכקוק: Periodically inspect all wiring and connections for signs of wear, damage, or loose contacts.
רייניקונג: Keep the ESC clean and free from dust, dirt, and moisture. Use a soft, dry cloth for cleaning. Avoid using solvents or harsh chemicals.
היץ מאַנאַגעמענט: Ensure the ESC has adequate ventilation during operation. Avoid operating in excessively hot environments.
Firmware דערהייַנטיקונגען: Check the FLIPSKY website or VESC project for firmware updates. Updating firmware can improve performance and add new features. Follow update instructions carefully.

8. טראָובלעשאָאָטינג

פּראָבלעם	מעגלעך סיבה	לייזונג
ESC גייט נישט אן.	No battery connection, incorrect polarity, faulty power switch, discharged battery.	Check battery connections and polarity. Ensure battery is charged. Test power switch.
Motor not spinning or erratic behavior.	Incorrect motor wiring, Hall sensor issue, incorrect VESC_TOOL configuration, motor fault.	Verify motor phase and Hall sensor connections. Re-run motor detection in VESC_TOOL. Check motor for damage.
ESC overheating.	Insufficient cooling, excessive load, incorrect current limits.	Improve ventilation. Reduce load. Adjust current limits in VESC_TOOL.
Communication issues with VESC_TOOL.	Incorrect USB driver, faulty USB cable, incorrect port selection in VESC_TOOL.	Install correct USB drivers. Try a different USB cable. Select the correct COM port in VESC_TOOL.
אומגעריכט שאַטדאַונז.	Protection limits triggered (voltage, קראַנט, טעמפּעראַטור).	Check VESC_TOOL logs for fault codes. Address the underlying cause (e.g., low battery, overcurrent, overheating).

9. וואָראַנטי און שטיצן

The FLIPSKY FSESC 110100 comes with a 2-חודש וואָראַנטי פֿון דעם קויפֿדאַטום. די וואָראַנטי דעקט פֿאַבריקאַציע־דעפֿעקטן אונטער נאָרמאַלע באַניץ־באַדינגונגען.

For technical support, troubleshooting assistance, or warranty claims, please contact FLIPSKY customer service through their official website or the retailer from whom you purchased the product. Please have your purchase receipt and product serial number available.

For the latest VESC_TOOL software and documentation, please visit the official VESC project webפּלאַץ: www.vesc-project.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.