SEQURE SQESC 14200 Pro Brushless ESC Instruction Manual

1. פּראָדוקט איבערview

The SEQURE SQESC 14200 Pro is a high-performance 200A Brushless Electronic Speed Controller designed for various RC applications, including crawler cars, helicopters, model ships, and off-road vehicles. It features a robust design with effective heat dissipation and supports a wide range of signal protocols and programming adjustments.

• פירמוואַרע: ESCape32, Processor: STM32G071
• אַרייַנשרייַב וואָלtage: DC 18V-59V (5-14S Lipo)
• קעסיידערדיק קראַנט: 200A, Peak Current: 350A
• Adjustable BEC: 6V, 7.4V, 8.4V, 12V (15A continuous, 35A peak)
• שטיצט פּראָטאָקאָלס: Dshot (All), PWM, Oneshot, Multishot, etc.
• אַוואַנסירטע פֿעיִקייטן: RPM specialized signal, throttle calibration, current detection, motor steering, telemetry signal, RGB LED light settings.
• שוץ: נידעריק וואָלtage, temperature, locked rotor, and current protection.

2. וואָס איז אין דער קעסטל

• Electric Speed Controller (SQESC 14200 Pro) x 1
• 5V Fan x 1
• 4*250mm Black Tie Straps x 2
• Hexagonal Screws x 10
• Transparent Heat Shrinkable Sleeve x 4

3. ספּעסאַפאַקיישאַנז

גשמיות דימענשאַנז: 16.3 X 1.8 X 1.49 אינטשעס. נומער וואָג: 11.2 אונסעס.

4. סעטאַפּ און ייַנמאָנטירונג

4.1 וויירינג דיאַגראַמע

Proper wiring is crucial for safe and optimal performance. Refer to the diagram below for connecting the ESC to your motor and battery.

The diagram illustrates the connections: Motor (A, B, C phases), Battery (DC 18V-59V, 5-14S Lipo), RPM, BEC, GND, S Signal, and TX Telemetry.

4.2 BEC VoltagE אַדזשאַסטמאַנט

The SQESC 14200 Pro features a dip switch system for adjusting the BEC output voltage. This allows precise adjustment to match your receiver and servo requirements.

פאַרזיכערן די ריכטיק וואָלtage is selected before powering on your system to prevent damage to connected components.

4.3 Installation Hole Position

Refer to the following diagram for the installation hole positions and dimensions to securely mount your ESC.

5. אַפּערייטינג ינסטרוקטיאָנס

5.1 Initial Power-Up and Throttle Calibration

Upon initial power-up, the ESC automatically detects the throttle signal. For optimal performance and safety, it is recommended to perform a throttle calibration with your transmitter. Consult your transmitter's manual for specific throttle calibration procedures.

5.2 Programming Parameters

The SQESC 14200 Pro supports visual programming parameter adjustment. This tool allows you to customize various settings such as motor timing, throttle calibration, current detection, motor steering, telemetry signal, and RGB LED color lights. Refer to the official SEQURE website for the latest programming software and detailed instructions.

5.3 אַפּפּליקאַטיאָן סינעריאָוז

The ESCape32 firmware makes this ESC suitable for a wide range of RC models requiring precise speed control and robust power delivery.

6. וישאַלט

To ensure the longevity and reliable performance of your ESC, follow these maintenance guidelines:

• היץ דיסיפּיישאַן: The ESC is equipped with a CNC metal radiator for effective heat dissipation. Ensure the radiator fins are kept clean and free from debris to maintain optimal cooling.



• קאַבלע אָרנטלעכקייַט: Regularly inspect all power and signal cables for any signs of wear, cuts, or damage. The high-quality twisted pair cables are designed to reduce interference, but physical damage can compromise performance.



• ריינקייַט: Keep the ESC clean and dry. Avoid exposure to moisture, dust, and corrosive substances.
• זיכער מאָונטינג: Ensure the ESC is securely mounted using the provided tie straps and screws to prevent movement and potential damage during operation.

7. טראָובלעשאָאָטינג

If you encounter issues with your SEQURE SQESC 14200 Pro, consider the following common problems and solutions:

• ESC Not Responding / No Power:
  • Check all power connections to ensure they are secure and correctly polarized.
  • Verify the battery is fully charged and functioning correctly.
  • Ensure the BEC voltage is set appropriately for your receiver.
• Motor Not Spinning / Incorrect Direction:
  • Perform a throttle calibration as described in Section 5.1.
  • Check motor phase connections (A, B, C). If the motor spins in the wrong direction, swap any two of the three motor wires.
  • Verify motor steering settings in the programming tool.
• Intermittent Operation / Signal Loss:
  • Inspect signal cables for damage or loose connections.
  • Ensure the twisted pair cables are properly routed and not exposed to excessive electromagnetic interference.
  • Check for any physical obstructions or debris affecting the ESC or motor.
• איבערהייצונג:
  • Ensure the ESC's metal radiator is clean and has adequate airflow.
  • Verify the 5V fan is operating correctly.
  • Check for excessive current draw from the motor or an undersized motor for the application.
• פּראָגראַממינג ישוז:
  • Ensure you are using the correct programming tool and firmware version (ESCape32) from the official SEQURE webפּלאַץ.
  • Verify the connection between the programming tool and the ESC.

8. זיכערקייַט אינפֿאָרמאַציע

No specific safety warnings were provided in the product description. However, when operating any high-power electronic speed controller and RC equipment, always observe the following general safety precautions:

• Always connect the battery last and disconnect it first.
• זיכער מאַכן אַז אַלע פֿאַרבינדונגען זענען זיכער און איזאָלירט צו פאַרמייַדן קורץ קרייזן.
• Never operate the ESC or motor without proper ventilation.
• Keep hands and loose clothing away from spinning propellers or moving parts.
• Use appropriate battery types and voltages as specified for the ESC.
• Store batteries and ESCs in a safe, cool, and dry environment.
• דעם פּראָדוקט איז רעקאָמענדירט פֿאַר באַניצער 16 יאָר און העכער.

9. שטיצן

For further assistance, technical support, or warranty inquiries, please contact SEQURE directly through their official webפּלאַץ אָדער די זיצער ווו די פּראָדוקט איז פּערטשאַסט.

באַזוכן די SEQURE Store on Amazon פֿאַר מער אינפֿאָרמאַציע און פּראָדוקטן.