Electro-Voice RE520 Handheld Condenser Microphone User Manual

1. הקדמה

This manual provides essential information for the proper use and care of your Electro-Voice RE520 Handheld Condenser Microphone. The RE520 is engineered for vocal performance, featuring a supercardioid polar pattern for excellent off-axis rejection and a wide frequency response tailored for the human voice. Please read this manual thoroughly before operating the microphone to ensure optimal performance and longevity.

2. פּראָדוקט איבערview

2.1 שליסל פֿעיִקייטן

• Supercardioid polar pattern for focused sound capture and feedback rejection.
• Wide frequency response (40Hz-20kHz) optimized for vocal clarity.
• Integrated 150Hz bass roll-off switch to reduce proximity effect and low-frequency rumble.
• Rugged Memraflex grille designed for durability and dent resistance.
• Requires 48V phantom power for operation.

2.2 וואָס איז אין דער קעסטל

• Electro-Voice RE520 Handheld Condenser Microphone

Figure 1: The Electro-Voice RE520 Handheld Condenser Microphone, showcasing its robust design and grille.

פיגור 2: א נאנטע בילד view of the RE520 model designation on the microphone body.

3. סעטאַפּ

3.1 פֿאַרבינדן דעם מיקראָפֿאָן

1. Ensure your audio mixer or interface is powered off before making connections.
2. Connect a standard 3-pin XLR cable to the microphone's output connector.
3. Connect the other end of the XLR cable to an available microphone input on your mixer or audio interface.
4. Activate 48V phantom power on the corresponding channel of your mixer or interface. The RE520 requires phantom power to operate.

Figure 3: The XLR output connector located at the base of the RE520 microphone for audio signal transmission.

3.2 מיקראָפאָן פּלאַצירונג

For optimal vocal performance, hold the microphone approximately 2-6 inches (5-15 cm) from your mouth. Experiment with distance and angle to achieve the desired tone and to minimize plosive sounds (P, B sounds). The supercardioid pattern is most sensitive directly in front of the microphone, providing excellent rejection of sounds from the sides and rear.

4. אָפּעראַציע

4.1 Bass Roll-Off Switch

The RE520 features an internal 150Hz bass roll-off switch. This switch is designed to reduce low-frequency rumble, stage noise, and the proximity effect (an increase in bass response when the microphone is close to the sound source). To access the switch:

1. Carefully unscrew the microphone grille.
2. Locate the small switch near the microphone capsule.
3. Toggle the switch to the desired position (flat or roll-off).
4. Gently reattach the grille, ensuring it is securely fastened.

פיגורע 4: אינערלעכער view of the RE520, highlighting the bass roll-off switch for low-frequency attenuation.

4.2 געווינען סtaging

געהעריק געווינס זtaging is crucial for optimal sound quality. Adjust the gain on your mixer or interface so that the input signal is strong without clipping (distortion). Monitor your levels carefully to prevent overloading the microphone or the input stage of your equipment.

5. וישאַלט

5.1 רייניקונג

• The Memraflex grille can be gently cleaned with a soft, dry cloth. For more thorough cleaning, the grille can be carefully unscrewed and wiped with a slightly damp cloth. Ensure the grille is completely dry before reattaching.
• Do not use harsh chemicals or abrasive cleaners on any part of the microphone.
• Avoid getting moisture into the microphone capsule.

5.2 סטאָרידזש

Store the microphone in a dry, dust-free environment when not in use. Protect it from extreme temperatures and humidity. Using a microphone pouch or case is recommended to prevent physical damage.

6. טראָובלעשאָאָטינג

6.1 קיין קלאַנג אַרויסגאַנג

• Check Phantom Power: Ensure 48V phantom power is activated on the connected mixer or interface channel. The RE520 will not operate without it.
• קאַבלע קשר: Verify that the XLR cable is securely connected at both the microphone and the input device. Try a different XLR cable to rule out a faulty cable.
• אַרייַנשרייַב געווינס: באַשטעטיקן אַז די אינפוט געווינס אויף אייער מיקסער אָדער אינטערפֿייס איז ריכטיק איינגעשטעלט און נישט אינגאַנצן אַראָפּגעדרייט.
• Mixer/Interface Settings: Check that the correct input channel is selected and not muted on your audio equipment.

6.2 Feedback Issues

• מיקראָפאָן אָרט: Position the microphone away from loudspeakers and monitors. The supercardioid pattern offers best rejection directly from the rear.
• געווינס רעדוקציע: Lower the input gain on your mixer or interface.
• יקוואַליזיישאַן: Use an equalizer to cut frequencies that are causing feedback.
• באַס ראָולינג: Engage the 150Hz bass roll-off switch if low-frequency feedback is an issue.

6.3 פאַרקרימט סאָונד

• אַרייַנשרייַב געווינס: Reduce the input gain on your mixer or interface. The signal may be too hot, causing clipping.
• פּראַקסימאַטי ווירקונג: If distortion is due to excessive bass, increase the distance between the microphone and the sound source, or engage the bass roll-off switch.

7. ספּעסאַפאַקיישאַנז

8. וואָראַנטי און שטיצן

Electro-Voice products are manufactured to high standards and are backed by a manufacturer's warranty. For specific warranty details, registration, or technical support, please refer to the official Electro-Voice webזייטל אדער קאָנטאַקט אייער אָטעריזירטן הענדלער. האַלט אייער קויפן באַווייַז פֿאַר וואָראַנטי קליימז.

For further assistance, visit the official Electro-Voice Store: Electro-Voice Store