Walfront 5V - 24V DC Motor Forward/Reverse Control Timing Delay Time Cycles Relay

הקדמה

This manual provides detailed instructions for the Walfront 5V - 24V DC Motor Forward/Reverse Controller. It covers product specifications, port descriptions, setup procedures, operating modes, and troubleshooting tips to ensure optimal performance and safe usage of your device.

ספּעסאַפאַקיישאַנז

פּאָרט דיסקריפּשאַנז

Understanding the function of each port is crucial for correct wiring and operation.

• DC 5.5mm Female: Power supply input 1 (DC 5V).
• VIN: Power supply input 2 positive (DC 6.5-25V).
• GND: Power supply input 2 negative.
• FWD: Forward input control. Note: This input is invalid in partial function modes.
• REV: Reverse input control. Note: This input is invalid in partial function modes.
• האַלטן: Stop input control. Note: This input is invalid in partial function modes.
• מ+: Motor positive terminal.
• מ-: Motor negative terminal.
• פּ+: Motor power supply positive terminal.
• פּ-: Motor power supply negative terminal.

סעטאַפּ

Follow these steps to set up your motor controller:

1. מאַכט קשר: Connect your power supply to the board. You have two options:
   • For DC 5V, use the 5.5mm DC female jack.
   • For DC 6.5-25V, connect to the VIN (positive) and GND (negative) terminals.

   Note: Do not connect both power sources simultaneously.

2. מאָטאָר קשר: Connect your motor to the M+ (positive) and M- (negative) terminals.
3. מאָטאָר מאַכט צושטעלן: Connect the motor's dedicated power supply to the P+ (positive) and P- (negative) terminals. This supply can be DC 1-110V or AC 85-265V.
4. Input Controls (Optional): If using external control signals, connect them to the FWD (forward), REV (reverse), and STOP (stop) input terminals.

אַפּערייטינג ינסטראַקשאַנז

אַפּערייטינג מאָדעס

The controller supports two input trigger modes:

• מאָדע 1: Low Pulse (falling edge trigger)
• מאָדע 2: Low Level (rising edge trigger)

טייַמער פאַנגקשאַנז

The device features three distinct timers for precise control:

• ט 1: Forward Timer - Controls the duration of forward motor movement.
• ט 2: Reverse Timer - Controls the duration of reverse motor movement.
• ט 3: Stop Timer - Controls the duration the motor remains stopped between cycles.

Time units can be set to 0.1 seconds, 1 second, or 1 minute.

Sequence Movement Indication

The LEDs on the board indicate the current motor status:

• Motor Forward: Relay 1 is active, Relay 2 is stopped. The F געפירט פלאַשיז.
• Motor Reverse: Relay 1 is stopped, Relay 2 is active. The R געפירט פלאַשיז.
• מאָטאָר סטאָפּ: Both Relay 1 and Relay 2 are stopped. The S געפירט פלאַשיז.

באַשטעטיק פֿאַבריק סעטטינגס

To restore the device to its default factory settings:

• Press and hold the "++" and "--" buttons simultaneously for 5 seconds.

מאַכט שפּאָרן מאָדע

This mode helps conserve energy by turning off the digital display and LED indicators while maintaining full functionality:

• אריינצוגיין: דריק און האלט דעם "OK" קנעפל פאר 5 סעקונדעס.
• צו אַרויסגאַנג: Press and hold the "OK" button again for 5 seconds.

וישאַלט

To ensure the longevity and reliable operation of your Walfront motor controller, follow these general maintenance guidelines:

• האַלטן ריין: Regularly clean the board with a soft, dry cloth to prevent dust and debris buildup, which can affect performance.
• ויסמיידן נעץ: Protect the device from moisture and extreme temperatures. Operate it within its specified environmental conditions.
• דורכקוקן קאַנעקשאַנז: קאָנטראָלירט פּעריִאָדיש אַלע דראָט פֿאַרבינדונגען צו זיכער מאַכן אַז זיי זענען זיכער און פֿרײַ פֿון קעראָוזשאַן. לויזע פֿאַרבינדונגען קענען פֿירן צו אומגעריכטע אָפּעראַציע אָדער שאָדן.
• געהעריק ווענטאַליישאַן: Ensure adequate airflow around the board, especially if operating under heavy loads, to prevent overheating.

טראָובלעשאָאָטינג

אויב איר טרעפט פּראָבלעמען מיט אייער מאָטאָר קאָנטראָללער, זעט די פאלגענדע געוויינטלעכע פּראָבלעמען און לייזונגען:

• מיטל נישט פּאַוערינג אויף:
  • Verify that the power supply is correctly connected to either the DC 5.5mm jack or the VIN/GND terminals.
  • פאַרזיכערן די מאַכט צושטעלן וואָלtage is within the specified range (DC 5V or DC 6.5-25V).
  • Check for any loose wires or damaged connections.
• Motor Not Responding to Control Inputs (FWD/REV/STOP):
  • Confirm that the control inputs are correctly wired and receiving the appropriate signals.
  • Note that FWD, REV, and STOP inputs may be invalid in certain partial function modes. Refer to the operating instructions for mode-specific behavior.
  • Ensure the motor's power supply (P+/P-) is correctly connected and providing power.
• Incorrect Timing or Sequence:
  • Review the timer settings (T1, T2, T3) and time units (0.1s, 1s, 1min) to ensure they are configured as desired.
  • If the sequence is unexpected, try resetting to factory settings (press "++" and "--" simultaneously for 5 seconds) and reconfigure.
• Digital Display/LEDs Off (but functions work):
  • The device might be in Power Saving Mode. Press and hold the "OK" button for 5 seconds to exit this mode.
• General Programming/Configuration Issues:
  • While specific programming steps are not detailed in the product description, ensure you are following the button press sequences accurately for setting timers and modes.
  • If persistent issues arise, consider contacting Walfront customer support for advanced programming guidance.

פּעקל אינהאַלט

The package includes the following item:

• 1 x Motor Control Board

וואָראַנטי און שטיצן

For warranty information and technical support, please refer to the seller's policies or contact Walfront customer service directly. Keep your purchase receipt for any warranty claims.