In Step 4 of the BONTEC MTR-B2 assembly, the screw positions on the top shelf do not align with the holes in the legs; am I inserting them incorrectly?

If the screw positions on the top shelf do not align with the holes in the side supports (legs) during Step 4 of the BONTEC MTR-B2 assembly, please check the following:Check Part Orientation: Ensure that the side support boards (from Step 2) and the middle shelf (from Step 3) are not installed upside down or backward. The pre-drilled holes for the cam locks must face the correct direction to receive the connecting screws from the top shelf.Verify Screw Installation: Confirm that the 4 connecting screws (Type A) were inserted into the correct pre-drilled holes on the underside of the top shelf board during Step 1.Loosen Previous Steps: Sometimes parts do not align if previous screws are overtightened. Try slightly loosening the cam locks from Step 3 to allow for minor adjustments, then align the top shelf and tighten everything once all pieces are in place.Do Not Force: The manual advises not to force parts together. If they do not align, it is likely that one of the boards is rotated incorrectly. Compare your current assembly to the Figure 3: Visual Assembly Guide in the manual to ensure the hole patterns match the diagram.If the holes still do not line up, there may be a manufacturing defect with the pre-drilled positions. In this case, you should contact BONTEC customer support for a replacement part.

BONTEC MTR-B2 2-Tier Wood Monitor Stand Riser Instruction Manual

הקדמה

This manual provides instructions for the assembly, operation, and maintenance of your BONTEC MTR-B2 2-Tier Wood Monitor Stand Riser. This product is designed to elevate your monitor to an ergonomic height, reduce neck and back strain, and organize your workspace with its integrated storage and cable management features.

פּראָדוקט פֿעיִקייטן

פּרעמיום קוואַליטי מאַטעריאַלס: Constructed from eco-friendly MDF wood with a smooth finish for durability and stability.
ערגאָנאָמיק פּלאַן: Elevates your screen by 5.6 inches to eye level, promoting healthier posture and reducing strain.
Spacious 2-Tier Storage: גיט ample space (21.3 inches wide) for laptops, keyboards, and other desk essentials.
ינטעגראַטעד קאַבלע פאַרוואַלטונג: Features a built-in system and cellphone holder to keep your workspace organized and clutter-free.
גרינג אַסעמבלי: Designed for quick and straightforward assembly.
סטאַביל פּלאַן: Includes soft rubber feet to ensure stability and protect your desk surface.

Diagram illustrating ergonomic benefits of a monitor stand — **Figure 1: Ergonomic Benefits.** This diagram shows the difference in posture with and without a monitor riser, highlighting how the stand helps maintain a straight back and reduces neck strain.

פּעקל אינהאַלט

Please verify that all components are present before beginning assembly. Refer to the assembly diagram for visual identification.

Top Shelf Board (x1)
Side Support Boards (x2)
Middle Shelf Board (x1)
Connecting Screws (Type A, x6)
Cam Locks (Type B, x6)
Wooden Dowels (Type C, x4)
Rubber Feet (Type D, x6)
Cable Management Clip (Type E, x1)

Assembly diagram showing all parts and steps for the monitor stand — **Figure 2: Assembly Components.** This image displays all individual parts and hardware included in the package, along with a step-by-step visual guide for assembly.

אַסעמבלי אינסטרוקציעס

Follow these steps to assemble your BONTEC MTR-B2 Monitor Stand Riser. A screwdriver is required (not included).

Step 1: Attach Connecting Screws to Top Shelf. Insert 4 connecting screws (Type A) into the pre-drilled holes on the underside of the top shelf board. Ensure they are securely fastened.
Step 2: Attach Wooden Dowels to Side Supports. Insert 2 wooden dowels (Type C) into the corresponding holes on the inner side of each side support board.
Step 3: Connect Side Supports to Middle Shelf. Align the middle shelf board with the wooden dowels on the side support boards. Secure the middle shelf to the side supports using 2 cam locks (Type B) on each side. Turn the cam locks clockwise until tight.
Step 4: Attach Top Shelf to Assembled Base. Align the top shelf (with connecting screws from Step 1) with the holes on the top edges of the assembled side and middle shelves. Secure the top shelf using the remaining 2 cam locks (Type B) on each side. Turn clockwise until tight.
Step 5: Apply Rubber Feet. Attach the 6 rubber feet (Type D) to the bottom corners and center of the stand to prevent scratching and ensure stability.
Step 6: Install Cable Management Clip. Attach the cable management clip (Type E) to the desired side of the stand for organizing cables.

Note: Do not overtighten screws to avoid damaging the wood.

Detailed step-by-step assembly instructions for the BONTEC monitor stand — **Figure 3: Visual Assembly Guide.** This diagram provides a visual representation of each assembly step, showing component placement and hardware usage.

אַפּערייטינג ינסטראַקשאַנז

Your BONTEC MTR-B2 Monitor Stand Riser is designed for versatile use to enhance your workspace.

מאָניטאָר אָרט: Place your monitor securely on the top surface of the stand. Ensure the monitor's base fits within the dimensions of the stand.
Keyboard Storage: Utilize the space beneath the middle shelf to store your full-size keyboard when not in use, freeing up desk space.
אַקסעסערי סטאָרידזש: The middle shelf and side compartments are ideal for organizing notebooks, pens, external hard drives, or other small office supplies.
Cellphone Holder: Use the integrated slot on the top surface to hold your cellphone upright. The slot is designed to allow charging cables to pass through for convenience.
קאַבלע פאַרוואַלטונג: Route power cords and data lines through the attached cable management clip to keep them tidy and prevent tangles.

Monitor stand in use with a monitor, phone, and speaker on top, and keyboard underneath — **Figure 4: Organized Workspace.** This image demonstrates the monitor stand in a typical setup, showcasing how it elevates the monitor and provides organized storage for various desk items.

Close-up of the monitor stand's phone holder with a phone and charging cable, and rubber feet — **Figure 5: Phone Holder and Stability.** א דיטיילד view of the integrated cellphone holder, showing a phone being charged, and the non-slip rubber feet at the base of the stand.

Cable management clip on the side of the monitor stand organizing power and data cables — **Figure 6: Cable Management.** This image highlights the cable management clip attached to the side of the stand, effectively organizing power and data cables.

Monitor stand with a full-size keyboard stored underneath — **Figure 7: Keyboard Storage.** The image shows a full-size keyboard neatly stored in the lower tier of the monitor stand, demonstrating efficient use of space.

וישאַלט

To ensure the longevity and appearance of your monitor stand, follow these simple maintenance guidelines:

רייניקונג: ווישן די ייבערפלאַך מיט אַ ווייך, דamp שטאָף. פֿאַרמײַדט ניצן שאַרפֿע כעמיקאַלן אָדער אַברייסיוו רייניגער, ווײַל זיי קענען שאַטן די ענדיקונג.
שטויב: Regularly dust the stand to prevent buildup.
סטאַביליטי טשעק: קאָנטראָלירט פּעריִאָדיש אַלע שרויפן און פֿאַרבינדונגען צו זיכער מאַכן אַז זיי בלייבן פֿעסט. פֿעסטשטײַערט ווידער אויב נייטיק.
ויסמיידן יבעריק וואָג: Do not exceed the maximum load capacity of 66 pounds (30 kg) to prevent damage or instability.
באַשיצן פון נעץ: Keep the stand away from excessive moisture or direct sunlight to prevent warping or discoloration of the wood.

טראָובלעשאָאָטינג

If you encounter any issues with your BONTEC MTR-B2 Monitor Stand Riser, refer to the following common solutions:

פּראָבלעם	מעגלעך סיבה	לייזונג
דער שטאַנד איז וואָקלדיק אָדער נישט סטאַביל.	Screws are loose; uneven surface; missing rubber feet.	Ensure all connecting screws and cam locks are tightened. Place the stand on a flat, stable surface. Verify all rubber feet are attached.
שוועריקייט בעת פֿאַרזאַמלונג.	אומרעכטע טייל אָריענטירונג; פעלנדיק האַרדווער.	Review the assembly instructions and diagrams carefully. Ensure parts are oriented correctly. Check package contents against the list. Do not force parts together.
Monitor does not fit on the stand.	Monitor base is too large for the stand's top surface.	Verify your monitor's base dimensions against the stand's top surface dimensions (21.26 x 10.04 inches).

ספּעסאַפאַקיישאַנז

אַטריביוט	דעטאַל
מאָדעל נומער	MTR-B2
סאָרט	BONTEC
מאַטעריאַל	אינזשענירטע האָלץ (MDF)
קאָליר	שוואַרץ
פּראָדוקט דימענשאַנז (L x W x H)	21.26 X 10.04 X 5.59 אינטשעס (540 X 255 X 142 מם)
פּונקט וואָג	7 פונט (3.17 קג)
מאַסע קאַפּאַציטעט	66 פונט (30 קג)
אַסעמבלי פארלאנגט	יא
ספּעציעלע שטריך	Lightweight, 2-Tier Storage, Cable Management, Cellphone Holder

Diagram showing the dimensions of the BONTEC monitor stand in millimeters — **פיגור 8: פּראָדוקט דימענסיעס.** This image provides a detailed diagram of the monitor stand's dimensions, including width, depth, and height, in millimeters.

פּראָדוקט ווידיאס

BONTEC 2-Tier Wood Monitor Stand Riser Overview

Video 1: Product Features and Installation Steps. דעם ווידעא גיט אַ פולשטענדיק איבערview of the BONTEC 2-Tier Wood Monitor Stand Riser, highlighting its key features, dimensions, and a visual guide for assembly. It demonstrates how the stand helps organize your desktop and supports a full-size keyboard.

BONTEC Extra Long 21.3 Inch 2 Tiers Wood Monitor Stand

Video 2: Detailed Product View. This video offers a closer look at the extra-long 21.3-inch BONTEC monitor stand, emphasizing its two-tier design and how it accommodates various desk setups for improved organization and ergonomics.

וואָראַנטי און קונה שטיצן

BONTEC is committed to providing high-quality products and exceptional customer service. If you encounter any issues with your monitor stand, please do not hesitate to contact our dedicated support team.

Our customer support is available to address any concerns you may have and ensure your experience is satisfactory. Please refer to your purchase documentation or the BONTEC webזייטל פֿאַר ספּעציפֿישע וואָראַנטי דעטאַילס און קאָנטאַקט אינפֿאָרמאַציע.

BONTEC MTR-B2