Moen R8736W Bathroom Safety 36-Inch Grab Bar Instruction Manual

1. הקדמה

The Moen R8736W Bathroom Safety 36-Inch Grab Bar is designed to provide secure support and enhance safety in your bathroom. Featuring a durable stainless steel construction and a Glacier White finish, this grab bar is ADA compliant and built for long-lasting reliability. Proper installation is crucial to ensure the grab bar provides the intended support.

2. זיכערקייַט אינפֿאָרמאַציע

• Always ensure the grab bar is installed securely into a wall stud or using appropriate SecureMount anchors (not included with all models) to support the stated weight capacity.
• Do not use the grab bar for purposes other than providing balance and support.
• Regularly inspect the grab bar for any signs of looseness, damage, or corrosion. If any issues are found, discontinue use immediately and address the problem.
• Wear appropriate safety gear, such as safety glasses, during installation.

3. פּעקל אינהאַלט

באַשטעטיקן אַז אַלע קאָמפּאָנענטן זענען פאַראַן איידער איר הייבט אָן די אינסטאַלאַציע:

• Moen R8736W 36-Inch Grab Bar
• ינסטאַלירונג אינסטרוקציעס
• Mounting Hardware (screws and washers)

4. מכשירים פארלאנגט פֿאַר ינסטאַלירונג

די פאלגענדע מכשירים זענען רעקאמענדירט פאר א געלונגענע אינסטאַלאַציע:

• בויער
• 1-1/4" Hole Saw (for hollow wall installation with SecureMount anchors)
• פיליפּס שרויפנ-ציער
• מדרגה
• בלייַער
• זיכערקייַט ברילן
• Stud Finder (if installing into wall studs)

5. אינסטאַלאַציע אינסטרוקציעס (סעטאַפּ)

This section provides detailed steps for installing your Moen grab bar. For visual guidance, please refer to the official installation video below.

5.1. פּלאַנירונג און פּלאַצירונג

Determine the optimal location for your grab bar. Consider areas where extra support is needed, such as near the toilet or inside the shower/bathtub. Ensure the chosen location allows for comfortable and safe use.

Figure 1: Recommended grab bar placement in a bathroom. Wall studs are indicated by thick lines. SecureMount Anchors allow installation without studs.

5.2. Marking Drill Points

1. Hold the grab bar in the desired position on the wall.
2. Use a level to ensure the bar is perfectly horizontal or vertical, depending on your chosen orientation.
3. Slide the end covers away from the flanges to expose the mounting plates.
4. Using a pencil, mark the center hole of each mounting plate on the wall.

5.3. Drilling Holes and Installing Anchors (for Hollow Walls)

If installing into a hollow wall (not directly into a stud), follow these steps using SecureMount anchors (sold separately):

1. Using a drill with a 1-1/4" hole saw, carefully drill a hole at each marked center point.
2. Insert a plastic guide sleeve into each hole until it is flush with the wall. Ensure the 'UP' indicator on the sleeve is pointing upwards.
3. Snap a pull tab onto each anchor.
4. Insert an anchor into each plastic guide sleeve and pull the tab towards you until it feels snug against the inside wall.
5. Remove the pull tab from each anchor by lifting it up and pulling it towards you.
6. Position a mounting plate over each plastic guide sleeve. The arrows on each mounting plate should point towards each other.
7. Secure the mounting plate in place with a bolt and two washers, tightening with a Phillips screwdriver.

5.4. Attaching the Grab Bar

1. Position the grab bar flanges over the installed mounting plates.
2. Secure the grab bar in place by inserting and tightening the three bolts and washers into each flange using a Phillips screwdriver.
3. Remove any protective covers from the hubs.
4. Slide the end covers back over each flange until they snap into place, concealing the mounting hardware.

5.5. ינסטאַלירונג ווידעא

For a visual guide on installing a grab bar with SecureMount Anchors, please watch the official Moen video below:

6. אפערירן (באַניץ)

Once properly installed, the Moen R8736W Grab Bar provides a stable and secure handhold. Use it to assist with balance when entering or exiting the shower/bathtub, or when standing up from a seated position. Always apply pressure directly to the bar and avoid hanging or swinging from it.

7. וישאַלט

To maintain the appearance and functionality of your grab bar:

• רייניקן רעגולער מיט אַ ווייכן, דamp שטאָף און מילדע זייף. פֿאַרמייַדן שרײַבנדיקע רייניגער, סאָלווענטן, אָדער שטרענגע כעמיקאַלן, ווײַל די קענען שאַטן די ענדיקונג.
• שווענקט גוט אויס נאכן רייניגן און טריקנט מיט א ווייכן טוך צו פארמיידן וואסער-פלעקן.
• Periodically check all mounting screws to ensure they remain tight and secure. Tighten if necessary.

8. טראָובלעשאָאָטינג

If you encounter any issues with your grab bar:

• Grab Bar Feels Loose: This is the most common issue. Immediately stop using the grab bar. Re-check all mounting screws and tighten them securely. If the issue persists, the mounting method may be insufficient, or the wall structure may be compromised. Consult a professional for re-installation or assessment.
• Corrosion or Rust: While made of stainless steel, prolonged exposure to harsh chemicals or standing water can affect the finish. Ensure proper cleaning and drying. If significant corrosion occurs, the structural integrity may be compromised, and replacement is recommended.

9. ספּעסאַפאַקיישאַנז

10. וואָראַנטי

The Moen R8736W Bathroom Safety 36-Inch Grab Bar is backed by Moen's Limited Lifetime Warranty. For specific terms and conditions, please refer to the warranty information provided with your product or visit the official Moen webפּלאַץ.

11. שטיצן

For further assistance, questions, or to purchase replacement parts, please contact Moen Consumer Services:

• טעלעפֿאָן: 1-800-BUY-MOEN (1-800-289-6636)
• Webפּלאַץ: באַזוכט דעם אָפֿיציעלן מאָען webזייטל פֿאַר פּראָדוקט רעגיסטראַציע, אָפֿט געשטעלטע פֿראַגעס, און נאָך שטיצע רעסורסן.