Cornat Tratto TR182 Two-Handle Basin מיקסער קראַן אינסטרוקציע מאַנואַל

1. הקדמה

This manual provides detailed instructions for the installation, operation, and maintenance of your Cornat Tratto TR182 Two-Handle Basin Mixer Tap. Please read this manual thoroughly before installation and use to ensure proper function and longevity of the product. Retain this manual for future reference.

בילד 1: The Cornat Tratto TR182 Two-Handle Basin Mixer Tap. This image displays the chrome-plated tap with its high, swivelling spout and two cross-handle controls for hot and cold water.

2. זיכערקייַט אינפֿאָרמאַציע

• שטענדיק אויסדרייען די הויפּט וואַסער צושטעל איידער איר הייבט אן קיין אינסטאַלאַציע אָדער וישאַלט אַרבעט.
• זיכער מאַכן אַז אַלע פֿאַרבינדונגען זענען זיכער צו פאַרמייַדן ליקס.
• אויב איר זענט נישט זיכער וועגן קיין טייל פון די אינסטאַלאַציע פּראָצעס, קאָנסולטירט אַ קוואַליפֿיצירטן פּלאָמבער.
• Do not use abrasive cleaners or harsh chemicals on the chrome-plated surface, as this can damage the finish.
• This tap is designed for high-pressure water systems. Ensure your water system is compatible.

3. פּעקל אינהאַלט

Please check that all components are present before starting installation:

• 1 x Cornat Tratto TR182 Basin מיקסער טאַפּ
• 1 x Connection Hose Set (350 mm length)
• 1 x Pull Drain Fitting (1 1/4 inch)
• Mounting Accessories (washers, nuts, etc.)

4. ספּעסאַפאַקיישאַנז

בילד 2: Diagram illustrating the dimensions of the Cornat Tratto TR182 tap, including total height (250mm), spout reach (137mm), and base diameter (55mm).

5. אינסטאַלאַציע (סעטאַפּ)

5.1 נויטיקע מכשירים (נישט אַרייַנגערעכנט)

• אַדזשאַסטאַבאַל מוטער-שליסל
• שרויפנ - ציער
• פּלאַמערס טייפּ (PTFE טייפּ)
• Basin שליסל (אפציאנאל, פאר ענגע פלעצער)
• Bucket and towels (for spills)

5.2 פאַר-ינסטאַלירונג סטעפּס

1. אויסלעשן די וואַסער צושטעל: Locate the main water shut-off valve for your home or the shut-off valves under the sink. Turn them off completely.
2. Drain Existing Water: Open the existing tap to drain any remaining water from the lines.
3. Remove Old Tap: Disconnect the water supply lines from the old tap and remove the mounting nuts. Carefully lift out the old tap and drain fitting.
4. ריין מאָונטינג ייבערפלאַך: Clean the sink or countertop surface where the new tap will be installed.

5.3 צאַפּ ינסטאַלירונג

1. צוטשעפּען פֿאַרבינדונג רערן: Screw the 350mm connection hoses into the base of the new tap. Hand-tighten first, then use a wrench for a snug fit, but do not overtighten.
2. Position Tap: Place the tap through the single mounting hole on your basin or countertop. Ensure any rubber gaskets or seals are correctly positioned between the tap base and the sink surface.
3. זיכערער צאַפּ: From underneath the sink, slide the rubber washer, metal washer, and mounting nut onto the threaded rod(s) of the tap. Tighten the mounting nut securely to hold the tap in place.
4. פאַרבינדן וואַסער צושטעלן: Connect the hot and cold water supply lines to the corresponding shut-off valves. Use plumber's tape on the threads for a watertight seal. Tighten with a wrench.

5.4 פליסן פּאַסן ינסטאַלירונג

1. אַסעמבאַל דריינאַדזש: Follow the instructions provided with the pull drain fitting (1 1/4 inch) to assemble it. Ensure all seals are correctly placed.
2. אינסטאַלירן דרעין: Insert the drain fitting into the drain hole of the basin. From underneath, secure it with the provided nut and washer, ensuring a watertight seal.
3. Connect Pull Rod: Connect the pull rod from the tap to the drain stopper mechanism. Adjust the rod to ensure the stopper opens and closes smoothly.
4. Connect to P-Trap: Connect the drain fitting to your existing P-trap assembly.

5.5 פּאָסטן-ינסטאַלירונג טשעקס

1. צוריקשטעלן וואַסער צושטעל: סלאָולי קער אויף די הויפּט וואַסער צושטעלן.
2. טשעק פֿאַר ליקס: Carefully inspect all connections under the sink for any signs of leaks. Tighten connections if necessary.
3. פלאַש ליניעס: Open both hot and cold handles on the tap to flush out any debris from the water lines. Let the water run for a few minutes.

6. אָפּעראַציע

The Cornat Tratto TR182 features two cross-handles for precise control of water flow and temperature.

• קאלט וואסער: Turn the right handle counter-clockwise to open the cold water supply. Turn clockwise to close.
• הייס וואַסער: Turn the left handle counter-clockwise to open the hot water supply. Turn clockwise to close.
• טעמפּעראַטור קאָנטראָל: Adjust the hot and cold handles simultaneously to achieve the desired water temperature.
• שפּוט דריי: The high spout can be swiveled to direct the water flow as needed.
• Drain Stopper: Use the pull rod located behind the tap to open and close the basin's drain stopper. Pull up to close the drain, push down to open.

7. וישאַלט

7.1 רייניקן דעם קראַן

• Clean the chrome-plated surface regularly with a soft cloth and mild soap or a non-abrasive cleaner specifically designed for chrome.
• שווענקט גוט אויס מיט ריינעם וואַסער און טריקנט מיט אַ ווייכן שטאָף צו פאַרמייַדן וואַסער פלעקן.
• Avoid using abrasive sponges, scouring pads, or harsh chemical cleaners (e.g., bleach, ammonia-based products) as these can damage the finish.

7.2 לופטער אויפהאלטונג

The tap features a low-noise aerator (M24 x 1) designed to provide a soft, water-saving jet. Over time, mineral deposits can accumulate in the aerator, reducing water flow.

1. Remove Aerator: Unscrew the aerator from the end of the spout. You may need an aerator key or a coin.
2. ריין: Rinse the aerator components under running water. Use a soft brush to remove any debris or mineral deposits. For stubborn deposits, soak the aerator in a solution of equal parts white vinegar and water for 30 minutes.
3. ריאַסעמבאַל: Screw the clean aerator back into the spout, ensuring it is hand-tightened.

7.3 קאַרטרידזש פאַרבייַט

The tap is equipped with easily replaceable cartridges featuring low-wear ceramic sealing discs. If you experience persistent dripping or difficulty controlling water flow, a cartridge may need replacement.

1. אויסלעשן די וואַסער צושטעל: Shut off the hot and cold water supply to the tap.
2. אַראָפּנעמען שעפּן: Carefully pry off the decorative cap on the handle (if present) and unscrew the handle screw. Remove the handle.
3. צוטריט קאַרטרידזש: Unscrew the retaining nut or ring that holds the cartridge in place.
4. פאַרבייַטן פּאַטראָן: Carefully lift out the old cartridge and insert a new, identical replacement cartridge.
5. ריאַסעמבאַל: Reattach the retaining nut/ring and the handle. Turn on the water supply and check for leaks.

8. טראָובלעשאָאָטינג

9. וואָראַנטי און שטיצן

For specific warranty information, please refer to the documentation provided at the time of purchase or contact Cornat customer support.

If you encounter issues that cannot be resolved using the troubleshooting guide, please contact your retailer or a qualified plumbing professional.

בילד 3: The official Cornat brand logo.