Performance Tool W1612 2.5 Ton Hydraulic Floor Jack User Manual

1. זיכערקייַט אינפֿאָרמאַציע

Always prioritize safety when operating the Performance Tool W1612 hydraulic floor jack. Failure to follow these instructions may result in serious injury or property damage.

• לייענען דעם מאַנואַל: Read and understand all instructions and warnings in this manual before using this product.
• ניצן אויף אַ שווערער, ​​גלייכער ייבערפלאַך: Operate the jack only on a hard, level surface capable of supporting the load. Avoid uneven or soft ground.
• נישט איבערשטייגן די קאַפּאַציטעט: Never exceed the rated capacity of 5,000 lbs (2.5 tons).
• ניצן דזשעק שטאַנדן: After lifting the vehicle to the desired height, always support it immediately with appropriately rated jack stands. The hydraulic jack is a lifting device only and is not designed to sustain loads for extended periods.
• צענטרירן די לאַסט: Ensure the load is centered on the jack saddle. Off-center loads can cause instability.
• טראָגן זיכערקייַט גאַנג: Always wear ANSI-approved safety goggles and heavy-duty work gloves during operation.
• האַלטן קלאָר: Keep hands, feet, and other body parts clear of moving parts and the vehicle during lifting and lowering.
• דורכקוקן איידער נוצן: Before each use, inspect the jack for any damage, leaks, or loose parts. Do not use if damaged.
• געהעריק סטאָרידזש: Store the jack in a clean, dry place, fully lowered, when not in use.

2. פּראָדוקט איבערview

The Performance Tool W1612 is a heavy-duty 2.5 ton (5,000 lb) hydraulic floor jack designed for lifting vehicles. It features a robust steel construction, wide front wheels, and a 360-degree swivel saddle for ease of use.

שליסל קאַמפּאָונאַנץ:

• ליפטינג אָרעם: The main arm that raises and lowers the vehicle.
• זאָטל: The contact point with the vehicle's lifting area.
• שעפּן: Used for pumping to lift and rotating to lower.
• מעלדונג וואַלוו: קאָנטראָלירט די נידעריגערע גיכקייט פון דער דזשעק.
• Wheels/Casters: Allow for easy positioning and maneuvering.

Figure 1: Performance Tool W1612 2.5 Ton Hydraulic Floor Jack. This image shows the overall design of the yellow hydraulic floor jack with its long handle and wheels.

פיגורע 2: זייַט view of the Performance Tool W1612 Hydraulic Floor Jack. This image provides a different angle of the jack, highlighting its low-profile design and robust construction.

3. סעטאַפּ

ערשט צוגרייטונג:

1. אויספּאַקן: Carefully remove the jack from its packaging. Inspect for any shipping damage.
2. שעפּן אַסעמבלי: Insert the handle into the handle socket and secure it according to the instructions provided in the packaging.

Bleeding the Hydraulic System:

Air can become trapped in the hydraulic system during shipping or use, affecting performance. Bleeding the system removes this air.

1. עפֿענען אויסלאָז ווענטיל: Turn the handle counter-clockwise to fully open the release valve.
2. פּאָמפּע שעפּן: Pump the handle 6-8 full strokes to force air out of the system.
3. שליסן אויסלאָז ווענטיל: דרייען די שעפּן קלאַקווייז צו פאַרמאַכן די מעלדונג וואַלוו.
4. טעסט: Test the jack by lifting and lowering it a few times without a load. If the jack does not lift smoothly or to its full height, repeat the bleeding process.

4. אַפּערייטינג ינסטרוקטיאָנס

הייבן א פאָרמיטל:

1. צוגרייטן פאָרמיטל: Park the vehicle on a hard, level surface. Engage the parking brake and block the wheels that will remain on the ground.
2. פּאָזיציע דזשעק: Position the jack directly under the vehicle's designated lifting point. Consult your vehicle's owner's manual for proper lifting points.
3. שליסן אויסלאָז ווענטיל: Turn the handle clockwise until the release valve is firmly closed. Do not overtighten.
4. ליפט פאָרמיטל: Pump the handle up and down to raise the vehicle to the desired height. Ensure the vehicle remains stable during lifting.
5. זיכער מיט דזשעק שטאנדן: Once the vehicle is at the desired height, immediately place appropriately rated jack stands under the vehicle's frame or designated support points.
6. Slightly Lower onto Stands: Slowly turn the handle counter-clockwise to open the release valve, allowing the vehicle to gently rest onto the jack stands. Remove the hydraulic jack once the vehicle is securely supported by the stands.

נידעריגער מאַכן אַ פאָרמיטל:

1. Reposition Jack: If removed, place the hydraulic jack back under the vehicle's lifting point and raise it slightly to take the load off the jack stands.
2. אַראָפּנעמען דזשעק סטאַנדז: פֿאָרזיכטיק אַראָפּנעמען די דזשעק שטאַנדן פֿון אונטערן פֿאָרמיטל.
3. נידעריקער פאָרמיטל: Slowly turn the handle counter-clockwise to open the release valve. Control the lowering speed by adjusting how much you open the valve.
4. Fully Lower: Once the vehicle is fully lowered, remove the jack.

5. וישאַלט

Regular maintenance ensures the longevity and safe operation of your hydraulic floor jack.

• הידראַולישע פליסיקייט לעוועל: Check the hydraulic fluid level periodically. With the jack fully lowered, remove the oil filler plug. The fluid level should be just below the filler hole. Top up with high-quality hydraulic jack oil if necessary. Do not use brake fluid or motor oil.
• שמירן: Lubricate all moving parts and pivot points with light machine oil monthly or as needed.
• רייניקונג: Keep the jack clean and free of dirt, grease, and corrosive materials. Wipe down the ram and pump plungers after each use.
• סטאָרידזש: Store the jack in a dry, protected area, fully lowered, to prevent rust and seal damage.

6. טראָובלעשאָאָטינג

7. ספּעסאַפאַקיישאַנז

• מאָדעל: W1612
• מאַסע קאַפּאַציטעט: 5,000 פונט (2.5 טאָן)
• מאַקסימום ליפטינג הייך: 19.25 אינטשעס
• מינימום הייבן הייך: Approximately 5 inches (standard floor jack minimums)
• מאַטעריאַל: אַללוי סטיל
• נומער וואָג: 79.7 פונט
• פּראָדוקט דימענשאַנז (L x W x H): 30.6 X 8.6 X 15.4 אינטשעס
• פאָרמיטל סערוויס טיפּ: מאַשין, טראָק

8. וואָראַנטי און שטיצן

For warranty information or technical support regarding your Performance Tool W1612 hydraulic floor jack, please refer to the documentation included with your purchase or contact Performance Tool customer service directly. Keep your purchase receipt for warranty claims.

פאַבריקאַנט: Performance Tool (Wilmar Corporation)

UPC: 039564124778

ערשטער דאַטע בנימצא: 1 אפריל 2004